Parvinbhai The 44-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and themagnitude of the force normal to the hinge axis AB in each of the small hinges A and B.Assume a = 19 in., b = 40 in., c = 14 in., d = 45 in.CDBb

Answered: Image /qna-images/answer/94855b70-ab6c-472e-be32-65f267777949.jpg

Answered: is held in the 90° open position by the…

is held in the 90° open position by the single prop CD. Determine the force F in the prop and the he hinge axis AB in each of the small hinges A and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: A package of mass m has a mass of 10 lbs. and rest on the platform, which is supported by the…

Q: The compound beam given in the figure is composed of a pair of beams, AB and BC, connected by a pin…

A: The compound beam given in the figure is composed of a pair of beams, AB and BC,connected by a pin…

Q: Data: r=0.25 inch, d=0.4 pig and h=0.5 inch, wi=2.5 inch and w= 1.5 inch. The forces fluctuate…

A: Where:Force = 14 Kips (tension) = 14,000 lbsForce = 5 Kips (compression) = -5,000 lbs (negative sign…

Q: A horizontal pipe line conveys a constant rate of flow which is measured by a venturimeter located…

A: When the manometer in inclined upward in the direction of flow,the deflection on a differential…

Q: A bicycle tire has a pressure of 9.41 x 105 N/m² at a temperature of 20.2°C and contains 1.92 L of…

A: Given data:To find:The final pressure of tire.

Q: Calculate the forces acting at pin A, pin B, and pin C. 6 m 5 kN 1.5 m y 1.5 m x OB 3 m 3 m

A: Calculate the forces acting at pin A, pin B, and pin C.

Q: determine the minimum allowable diameter in section B and C.

A: Permissible stress is stress which is produced due to pressure or forces which do not exceed the…

Q: Problem 16.137 At the instant shown in (Figure 1), rod AB has an angular velocity WAB = 3.0 rad/s…

Q: Figure F4-11 Full Alternative Text F4-12. Determine the components of reaction that the thrust…

Q: a) Relative and absolute humidity and dew temperature of the atmosphere. b) Absolute humidity and…

A: To calculate the relative, absolute humidity, and dew point temperature of the atmosphere and…

Q: Discuss the concept of hybrid systems and the modeling approaches used to address systems with both…

A: This question is based on the concept of hybrid system and modelling approach used.

Q: 3. For the two-bar structure shown below, determine the global stiffness matrix K and the force…

A: Formulating the elements based on the case you are solving is the initial step in solving any FEA…

Q: 11.4. Calculate RP.M. in Example 11.2.

A: Given:To find:Value of Reynold's number, .

Q: Consider the truss shown in the figure, built from three struts attached by three pins. The truss…

A: Consider the truss shown in the figure, built from three struts attached by three pins. The truss…

Q: The wheel is subjected to a torque of M 50 N m. If the coefficient of kinetic friction between the…

Q: Problem 2. (a) Calculate the fraction of atom sites that are vacant for copper (Cu) at its melting…

A: To determine:a)Fraction of atom sites that are vacant for cu at its melting pointb)Fraction of atom…

Q: constant temperatures of 60°C and 190°C, respectively. Determine the water convection heat transfer…

Q: Q3/ Decide if the copper wire made of ( 4 mm) in diameter is fail or not when it used for pulling a…

Q: Learning Goal: A material is homogenous and isotropic when it has a modulus of elasticity that does…

A: Note:- The last question is not interlinked.As per honor code and answering guidelines I can answer…

Q: P3: The resisting force R of a supersonic plane during flight can be considered as dependent upon…

A: The resisting force is dependent upon length of aircraft,(l), velocity (V), air viscosity (), air…

Q: 1. The figure shows a frame with negligible mass, keeping a 50-lb weight in equilibrium. The smooth…

Q: . Using a project start time of 0 (or January 1) and a required project completion time of 180 days…

A: Given:To find:Produce a bar chart (gantt chart) based on the es and ef times from the schedule

Q: The cars on the amusement-park ride rotate around the axle at A with a constant angular velocity…

A: The angular velocity frame is .The angular velocity of axle is .

Q: Determine the temperatures on the two sides of the circuit board.

A: To determine the temperatures on both sides of the board.given dimensions of the boards aslength…

Q: If I have a cylindrical plug of sandstone 1 m long with a diameter of 3 cm, and with permeability…

A: To determine:the rate needed for the flow to atmospheric pressure.Given:The length of the plug is…

Q: f 800 MPa, and a tensile this specimen experienc long? Why or why no

Q: Ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a…

A: The inlet pressure at the inlet of expansion valve is The inlet temperature at the inlet of…

Q: Question 3 For the beam loaded and supported as shown in Figure below, determine the deflection of…

Q: For the the given beam calculate the deflection of the beam at the center point and the reaction…

Q: Determine the Cartesian components, X and Y of force F2 if the sum of the moments created by F1 and…

Q: With a base schedule as shown below, what changes will occur if activity C can start after B is…

A: Here alphabets indicate activity and numbers indicate activity processing time.

Q: Problem 98. The drive mechanism imparts to the semicircular plate simple harmonic motion of the form…

A: Simple harmonic motion,

Q: The three rods are made of A-36 steel and form a pin-connected truss as shown. The assembly is…

Q: The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and…

A: Initially, we will disassemble the apparatus and create the conveyor's free-body diagram.The baggage…

Q: Develop an equation for the transmitted wave height behind a vertical wall extending a depth d into…

Q: For the beam cross section shown, bending is about the z axis. All dimensions are in inches and,…

Q: Assume the tanks are at steady-state (i.e. concentration within each tank is not changing with time)…

Q: Need only a handwritten solution only (not a typed one).

Q: (Make a MatLab code) Using for loop, write a script that will generate the all following…

A: Given:To find:Create a Matlab code.

Q: How much heat, in kJ, was added during the cycle? Round to two decimal places Hint: Don't forget…

A: The mass of working fluid is .The heat is added at temperature and the fluid changes from saturated…

Q: Prepare the following Stress and Strain Graph and Explain. carbon steel, cobalt, aluminum, and…

A: Carbon Steel:Elastic area: The elastic area of carbon steel usually shows a linear connection…

Q: Compute the Reynolds number of water pw 1000 kg/m³, w = 1 × 10-³kg/(m.s) flow inside a channel of…

Q: Calculate the force required by the hydraulic cylinder of a utility lift vehicle as shown in the…

Q: Please provide a visual, step-by-step lesson on how to create this solid model in solidworks, thank…

A: Assume the units are in mm.Open Part workbench in SolidWorks software and set the units to…

Q: QUESTION 1 In an arc welding operation, a groove weld has a cross sectional area=0.055 in2 and is 24…

Q: a) Estimate the thermal conductivity along a copper film with various thicknesses: d = 400, 100, and…

Q: A double-pipe heat exchanger is constructed of a copper (k =380 W/m*K) inner tube of internal…

A: The thermal conductivity of pipe is .The inner diameter of inner tube is .The outer diameter of…

Q: 5.5 Find the shear flow for the three-stringer section shown in Fig. 5.33 for V₂ = 5000 N and V, 0.…

A: (a) Assume that there is no bending ability for the thin sheets. In order to get the centroid of…

Q: oist in Egure 1) supports the 135 kg engine Determine magnitude of the force the load creates in…

Q: Sealed inside a rigid, poorly insulated vessel is 3 m^3 of diatomic nitrogen. The system is at 1…

A: To Find:the time interval in hours before the vessel ruptures.Given:The initial volume of nitrogen…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Parvinbhai

The 44-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the
magnitude of the force normal to the hinge axis AB in each of the small hinges A and B.
Assume a = 19 in., b = 40 in., c = 14 in., d = 45 in.
C
D
B
b

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculate the force in prop

VIEW

Step 3: Calculate the force in hinge A and B

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The three bars are welded together to form a rigid unit that is supported by three slider bearings. Neglecting the weights of the bars, determine the magnitudes of the three bearing reactions caused by the 120-lbin. couple.
The 48-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the magnitude of the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B. Assume a = 19 in., b = 40 in., c = 10 in., d = 36 in. Answers: F= A = B = i 15.9 i lb ! lb ! lb
The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B. Answers: F = A = 13" B = X X 47" D Elb lb lb B 44" 23"
The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the magnitude of the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B. Assume a = 22 in., b = 46 in., c = 11 in., d = 49 in. Answers: F = A = B = i i i lb lb lb B
Statics of Rigid Bodies (Equilibrium of Rigid Bodies) The 25-kg rectangular access door is held in the 90°open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to th.e hinge axis AB in each of the small hinges A and B. 3. B 300 mm 1200 mm 1000 mm 600 mm
The 41-lbrectangular access door is held in the 90° open position by the single prop CD. Determine the force Fin the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B. Assume a= 22 in., b= 36 in., c- 13 in., d= 49 in. Answers: F= Ib A- Ib B- Ib
The force P on the handle of the positioning lever produces a vertical compression of 56lb in the coiled spring in the position shown. Determine the magnitude of the corresponding force exerted by the pin at O on the lever. Assume a = 3.4in. b = 8.6in.
Determine the magnitude of the forces in pins B and D of the four-member frame. B = 56.3 lb, D = 125.8 lb B = 225 lb, D = 503 lb B = 125.8 lb, D = 112.5 lb B = 503 lb, D = 225 lb
Determine the axial forces in 600 lb E members CD and CB of the truss 4ft 4ft -3 ft 3 ft
One of the smooth vertical walls supporting end B of the 145-kg uniform shaft is turned through a plane. Calculate the magnitudes of the forces P and R exerted on the ball end B of the shaft by the vertical walls C and D, respectively. 27° angle as shown here. End A is supported by the ball-and-socket connection in the horizontal x-y Assume a = 6.4 m, b = 1.9 m, L = 7.3 m, and 0=0= 27°. %3D B -y 9.
The hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 33°, determine the force that must be applied to the rope, Frope, to lift a load of 4.7 kN. The three- pulley and hook assembly at the center of the system has a mass of 28.5 kg with a center of mass that lies on the line of action of the force applied to the hook. cc 130 BY NC SA 2013 Michael Swanbom Note the figure may not be to scale. Frope KN B A Fhook Frope