In the overhead view of the figure, five forces pull on a box of mass m = 3.3 kg. The force magnitudes are F = 11 N, F, = 19 N, F3 = 2.8 N, F4 = 15 N, and Fs = 4.3 N, and angle 84 is 34°. Find the (a) x-component and (b) y-component of the box's acceleration, and also give the acceleration as (c) a magnitude and (d) an angle relative to the positive direction of the x axis. (Note that the angle will be negative if it is below the horizontal.)

In the overhead view of the figure, five forces pull on a box of mass m = 3.3 kg. The force magnitudes are F = 11 N, F, = 19 N, F3 = 2.8 N, F4 = 15 N, and Fs = 4.3 N, and angle 84 is 34°. Find the (a) x-component and (b) y-component of the box's acceleration, and also give the acceleration as (c) a magnitude and (d) an angle relative to the positive direction of the x axis. (Note that the angle will be negative if it is below the horizontal.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the figure. A plot of potential energy U versus position x of a 2 kg particle that can move along x-axis. The graph has these values U_A=9J, U_C=20J and U_D=24J. The particle is released at position x=5 m with kinetic energy 4 J where the potential energy is U_B=12 j. What is the kinetic energy of the particle at x =3.5 m. Upt ... Uc UAF-- 4 6 7 x (m) A) 8J B none of them C 7J D 7.5J
For the system displayed in the figure below, the lengths of rigid-body OA and AB are l₁ = 6 m, 1₂ = 4 m. For the configuration shown, 0 = 65°, y = 68⁰, h = 1.5 m; the small roller B has velocity v = 5.5 m/s and acceleration a = 5.8 m/s² at its center. C and D are respectively the midpoint of rigid-body OA and AB. Determine the velocity and acceleration of C perceived by an observer who is at D and rotating with AB. Ꮎ C 1₁ 12 D BO P a V
Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see Wikipedia for more info). Luckily for us, this also makes for an interesting dynamics problem! At the instant shown, the crank arm's angular velocity is waB = 2,000 rpm (rotating clockwise) and the angle 0 = 40° with respect to the horizontal. Length of bar AB is r1 = 3 in. and the length of bar BD is r2 = 8 in. a) Clearly define coordinate systems for each link and write transformation arrays for each. b) Compute the velocity of point B in ft/s. Express your answer in rectangular coordinates. [Ans. to Check: 33.66 i– 40.11 j ft/sec] c) Determine the magnitude of the speed of the piston P in ft/s. Note: all answers should be positive since we only want to know the magnitude of the speed, not the direction (the piston can only move in the horizontal direction). [Ans. to Check: 43.6 ft/s] r2 10 B
The below figure shows a cylinder of 13 kg mass, 0,3 m radius, undergoing unconstrained planar motion under the action of two forces F1=181 N and F2=76 N as shown. Calculate the angular acceleration of the cylinder in rad/s2. (Hint: I=½mr2) (If the direction of the angular acceleration is CCW, just enter the value of it without any sign. If it has CW direction, enter "-" sign "negative sign" before the value such as "- 12,12". Allowable tolerance for this question is relatively 2 percent.) F2 Fi
An object of mass 350 gm. is attached to a light cord revolves in a horizontal circular path as in the figure. Find the angle 0, the radius of the circular path, the velocity and the centripetal acceleration if the tension .in the cord is 35N ZE 1 30cm إضافة ملف
In the figure, link 2 rotates with constant annular velocity CO2. A slider link 3 moves outwards with a constant relative velocity where Q is a Point on slider 3 and P is a point on link 2. The magnitude and direction of Coriolis component of acceleration is given by Q on 3 VOP 002 -P on 2
3. For the crank-slider type linkage shown, joints B and Y are coincident. Link AZ rotates as the link BA slides through a prismatic joint which can rotate with respect to the ground Y. What type of linkage is this? Draw the kinematic diagram and write down the constraint equations using the notation RAZ denotes the position of joint A relative to joint Z. If ZYZA = 45°, |AZ| = 10 cm, and |ZY| = 30 cm, what is the length |BA|?
A car is modeled as shown in Figure. Derive the equations of motion and find matrix M, C, and K. Mass = M, mass moment of inertia = JG .000 m1 k₂ F1 1 k2 000 k₁ k₁ m2 F2, X2 ell
A. The mechanism shown is used to feed cartons to a labeling machine. The drive shaft rotates clockwise. The ram weights 1.5 lb and the coefficient of friction between the ram and the machine is 0.2. Gravitational acceleration: g = 386 in/s². The weight of all other links is negligible. The linear ram acceleration is 5378 in/s² (horizontal direction, sense: to the left). 1. Draw the kinematic diagram. 2. For the instant shown, determine the torque required from the drive shaft to operate the ram. 3" -40° Connecting rod Ram
In the figure below, the ramp and two objects are located inside the elevator. The elevator moves up with acceleration= a. calculate s.. using the D'Alembert principle. The ramp is fixed.
The system of pulleys and weights shown in the figure is in the field of gravity. Write the Lagrangian equation of type I of the system. Calculate the acceleration of each bead.
A Ferris wheel with radius 30 ft is decelerating such that at t = 0 s, the tangential speed of a point P on the rim is v=10ft/s and dv/dt = ct. c=-0.4ft/s^3 . What is the acceleration of P at t= 3 s?