In the figure, the block of mass m is at rest on the inclined plane. Which of the following is true? normal force N mg sine 0 0 mg friction force f mg cose The static friction is equal to µmg sine. The static friction is equal to µmg tane. The static friction is equal to µmg cose. O The static friction is equal to µmg.

In the figure, the block of mass m is at rest on the inclined plane. Which of the following is true? normal force N mg sine 0 0 mg friction force f mg cose The static friction is equal to µmg sine. The static friction is equal to µmg tane. The static friction is equal to µmg cose. O The static friction is equal to µmg.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter6: Applications Of Newton's Laws

Section: Chapter Questions

Problem 47P: (a) What is the maximum frictional force in the knee joint of a person who supports 66.0 kg of her...

See similar textbooks

Similar questions

Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to either side. As they lift and hold it up so that it is motionless, each handle makes a different angle with respect to the vertical side of the chest (Fig. P5.76). If the angle between Jamals handle and the vertical side is 25.0 and the angle between Dayos handle and the vertical side of the chest is 30.0, what are the tensions in each handle? FIGURE P5.76
A push of magnitude P acts on a box of weight W as shown in the figure. The push is directed at an angle 0 below the horizontal, and the box remains a rest. The box rests on a horizontal surface that has some friction with the box. The normal force on the box due to the floor is equal to: O W + P cos 0. O W + P sin 0. OW-P sin 0. O W + P. O W. W 0 P
The 500-N block on an incline is acted upon by a force P at an angle from the horizontal. The coefficient of static friction is 0.25. If 0 = 0 deg, compute the value of force P necessary to (a) just start the block up the incline and (b) just prevent motion down the incline. 500 N P
The force needed to get a block moving and to just barely keep it moving were used to calculate the coefficient of static friction and the coefficient of kinetic friction for the block. Which values are most likely the correct ones for this block? O .35 for coefficient of static friction and .35 for coefficient of kinetic friction 25 for coefficient of static friction and .35 for coefficient of kinetic friction 35 for coefficient of static friction and .25 for coefficient of kinetic friction 25 for coefficient of static friction and .25 for coefficient of kinetic friction
In the figure, the block of mass 2.00 kg accelerates down the inclined plane. The coefficient of kinetic friction is 0.200 and angle of the inclined plane is 30.0°. What is the acceleration of the block? normal force N friction force f mg sine mg cose mg O 3.05 mis? O 5.05 m/s? O 2.05 m/s? O 4.05 m/s?
The 121-lb force P is applied to the 250-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.45, μk = 0.36. Answer: F= i lb
The coefficient of kinetic friction between a box and the floor is μk = 0.14 and the coefficient of static friction is μs = 2.0μk. Calculate the ratio of static to kinetic friction force if m = 8 kg.
Timmy is done placing his things in a big box and ready to transfer to his new condo unit. The movers arrived and uses a wooden ramp with an elevation of 24.6° from the horizontal to load his things to the truck. If the box has a mass of 45.7kg and has a value of coefficient static friction is 0.936. How much force is required for the delivery man to overcome the static friction? O 568.16 N O 385.14 N O 381.54 N O No answer O 586.16 N
moodle.nct.eduom/mod/qi -Learning Portal Courses - Reports - e-Services- Academic Departments - ETC - CIMS - A 17kg crate resting on a horizontal surface is pushed as shown. If the coefficient of static friction u, between the surfaces is 0.24, what is the minimum force (F) required to start the motion? O a 4.08N O b. 70.83N Oc 39.98N Od. 694.17N Windows buut An object of mass Skg is sliding with a constant velocity of 10m/s on a frcitionless horizontal table. The force needed to keep the object moving with the same velocity is. 144 4- # 4. 6. V.
The 137-lb force P is applied to the 240-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.51, Mk = 0.39. P Answer: F = i Mk lb
A 98N force is needed to push a 45kg box across the wooden floor. What is the value of the coefficient of static friction across the floor and the box? O 0.212 O 0.222 O No answer O 0.122 O 0.012
I 00LLJ408 - Go.. Question Info and Solutions Blocks A and B of mass 5 kg and 10 kg respectively are placed on a Smooth inclined plane of Inclination 30, as shown. Block A and B are subjected to forces 5 N And 50 N respectively along the incline, as shown. The coefficient of friction between A andBis 0.50 find the frictional force between A and B in N is: (g= 10 ms SOH 300 Options Solution Fs=Static frictional force umg cos 30 (0.5) (5) (10) cos 30 21.6 N Let a be the acceleration of both the blocks along 5.27 PM