In the figure below, this "double" nozzle discharges water (at 10°C, density= 1000 kg/m3) into the atmosphere at a rate of 0.50 m3/s. The pressure at the inlet is to be 315612 Pa. If the nozzle is lying in a horizontal plane. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe (1) is 30 cm in diameter. The x-component of force (Rx) acting through the flange bolts is required to hold the nozzle in place is:

In the figure below, this "double" nozzle discharges water (at 10°C, density= 1000 kg/m3) into the atmosphere at a rate of 0.50 m3/s. The pressure at the inlet is to be 315612 Pa. If the nozzle is lying in a horizontal plane. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe (1) is 30 cm in diameter. The x-component of force (Rx) acting through the flange bolts is required to hold the nozzle in place is:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Clear my choice In the figure below, this "double" nozzle discharges water (at 10°C, density= 1000 kg/m3) into the atmosphere at a rate of 0.50 m3/s. The pressure at the inlet is to be 315612 Pa. If the nozzle is lying in a horizontal plane. Jet A is 10 cm in diameter, jet B is 12 cm in diameter, and the pipe (1) is 30 cm in diameter. The x-component of force (Rx) acting through the flange bolts is required to hold the nozzle in place is: Pm V=26.1 m/s V-26.1 m/s Rx P-315612 Pa V =7.07 m/s Select one: 11:47 AM ENG 6/14/2021
A three-arm sprinkler is used to water a garden by rotating in a horizontal plane. Water enters the sprinkler along the axis of rotation at a rate of 40 L/s and leaves the 1.2-cm-diameter nozzles in the tangential direction. The central sprinkler bearing applies a retarding torque of 50 N-m due to friction at the anticipated operating speeds. Part A For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the rate of rotation of the sprinkler. Express your answer to three significant figures. V ΑΣφ I1 vec ? W = rad/s Submit Request Answer
Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1 tapering to 3.40 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s(b) point 2 m/s
Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y = 11.5 cm below point 1. The water pressure at point 1 is 3.20 ✕ 104 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 m/s (b) point 2 m/s.
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPa
Determine the magnitude and direction of the resultant force exerted on this double nozzle by water flowing through it as shown in the figure below. Both nozzle and jet have a velocity of 8.6 m/s and 11.5 m/s. The axis of both nozzles lies in a horizontal plane. 8.6 vnN 12 cw Jet 17 Cm 7270 * 11.5 /se 8.6 jet
A ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which is there to stabilize the weight). The jet leaving the orifice at the bottom has an upward velocity of 10 m/s, and the jet diameter at the exit is 2 cm. Assuming the jet spills sideways at 90°, find the height h at which the ball will float. Jet D1 =0.02 m W1 = 10 -
A reducing elbow is used to deflect water flow at a rate of 30 kg/s in a horizontal pipe upward by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into an atmosphere. The cross sectional area of the elbow is 150 cm² at the exist. The elevation difference between the centers of the exist and the inlet is 40 cm. The mass of the elbow and the water is 50 kg. Determine the anchoring force needed to hold the elbow in place. (Ans: 1.18 kN) 150 cm 40 cm Water
Answer the following questions: a. Air lows past an object and exits as a free jet as shown in the figure. Because of the obstruction, the exit velocity is non-uniform with magnitude of 4 m/s from r = 0 to r=0.5 m and 12 m/s from r = 0.5 m/s to r = 1.0 m. It is initially calculated that the average velocity is 10 m/s, using a differential area, dA=2rrdr, what is the value of the momentum correction factor, B? 2-m-dia. a Air Wake 1-m dia. Exit -4 m/s -12 m/s b. A hydraulic turbine has 85 m of head available at a flow rate of 250 L/s. If the fluid is water and the turbine's overall efficiency is 78%, what is the mechanical power, in kW, it extracts from the water?
100 mm 4. Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 60 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of u from the tangential direction, as shown in the figure. The length of each sprinkler arm is 0.45 m. Disregarding any frictional effects, determine the rate of rotation n of the sprinkler in rev/min for (a) 0 =0°, (b) 0 =30° r=0.45 m
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
The entrance flow between two parallel plates (gap h) has a velocity that varies linearly at the entrance and develops into a fully parabolic profile at the exit. What is the relationship between the maximum velocity at the entrance and that at the exit? You can show by symmetry that the maximum velocity is attained at the mid-plane between the two plates.