In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation are as follows: 1. Activate the lever of the 4/2 DCV to start the process 2. Cylinder A and Cylinder B clamps the workpiece at the same time 3. Activate the second DCV (4/2 DCV with spring return) to drill cylinder lowers the drill and raises afterwards (use the throttle valve and check valve to control the speed of the drill low). drill up is normal speed. 4. Once the drill is raised completely, operate the lever to retract cylinder A and cylinder B. Note: provide the following clearly 1. List of the components required 2. Hydraulic circuit with description to each component 3. state diagram should present the sequence of operation sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B sensors Figure 1: Drilling Process a) Design the Hydraulic Circuit with proper labeling. Include the components required b) Draw the Displacement -step diagram & Displacement -time diagram for the position of DCV cylinders A, B and drill

In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation are as follows: 1. Activate the lever of the 4/2 DCV to start the process 2. Cylinder A and Cylinder B clamps the workpiece at the same time 3. Activate the second DCV (4/2 DCV with spring return) to drill cylinder lowers the drill and raises afterwards (use the throttle valve and check valve to control the speed of the drill low). drill up is normal speed. 4. Once the drill is raised completely, operate the lever to retract cylinder A and cylinder B. Note: provide the following clearly 1. List of the components required 2. Hydraulic circuit with description to each component 3. state diagram should present the sequence of operation sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B sensors Figure 1: Drilling Process a) Design the Hydraulic Circuit with proper labeling. Include the components required b) Draw the Displacement -step diagram & Displacement -time diagram for the position of DCV cylinders A, B and drill

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
This course Is this armature winding a progressive or a retro-progressive winding? 3. d х у a Select one: O a. Both O b. Progressive OC. Neither O d. Retro-progressive
Compare between squirrel cage rotor and solid iron rotor
What are the two necessary conditions for a thyristor to begin conduction?and Once a thyristor begins to conduct, what condition(s) is necessary to cease conduction? Also, why is the conduction angle greater with an inductive load than with a purely resistive load?
Is this armature winding a progressive or a retro-progressive winding? W N Select one: 2 B 4' O a. Both O b. Progressive OC. Neither O d. Retro-progressive B S
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
Cylindrical metallic parabolic trough solar thermal collectors. 1. Does not rotate. 2. It rotates around one axis only. 3. It rotates around two axes only. 4. They can produce a temperature of20-100 °C. 5. They can produce a temperature of200-400 °C. 6. They can produce a temperature of2000-4000 °C. O 1 + 4 only. O 2 + 5 only. 2 + 6 only O 3 + 5 only.
Please show full work. Thank you
For the figure shown below if the current is moving clockwise around the coil. Which direction does the coil rotate? S O The whole coil moves down. The whole coil moves up. The right side goes down, and the left side goes up. The right side goes up, and the left side goes down.
What are the rotating parts on d.c machine. commutator segments O brushes O inter-pole O pole shoe
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O