In the circuit shown below. Let Vm-35 V and i-20 mA and Voo -0.7 V: iD 3 kQ 0.8 kO V„cos(ot)V For t 0s, the current in the diode equals: Oa. 0 mA Ob. 4 mA Oc. 2 mA Od. 6 mA If t = T/4, then the current in the diode equals: Da. 6.29 mA Ob. 5.03 mA Oc. 4,03 mA Od. 7.86 mA If t = T/2, then the current in the diode equals: Oa. 15.24 mA Ob. 13.24 mA Oc. 19.24 mA Od. 17.24 mA

In the circuit shown below. Let Vm-35 V and i-20 mA and Voo -0.7 V: iD 3 kQ 0.8 kO V„cos(ot)V For t 0s, the current in the diode equals: Oa. 0 mA Ob. 4 mA Oc. 2 mA Od. 6 mA If t = T/4, then the current in the diode equals: Da. 6.29 mA Ob. 5.03 mA Oc. 4,03 mA Od. 7.86 mA If t = T/2, then the current in the diode equals: Oa. 15.24 mA Ob. 13.24 mA Oc. 19.24 mA Od. 17.24 mA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 k0. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: a. + e. None Ob. 580mA Oc. 850mA Od 245mA 425mA D C: www tu Vo Q6
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Questions 1 V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 kn. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: None b. 580mA 850mA O c. Od 245mA O e. 425mA D C C: R www Q+ Vo
2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. UTM &UT ID 4 5UTM 3TM UTM UTM &UTM 5 UTM & UTM UTM 3 UTM 03 TM 6 UT 0.68 (a) UTM VD Figure A.1 State one possible reason why the diodes have different knee voltage values. UTM OM & UTM 3 UTM & TM (b) Based on Figure A.1, identify the knee voltage of UTM" TM 5 UTde BE UTM
For the circuit shown below, the diode cut in voltage is Vy0.7V. Th value of I, varies over the range 0 s l, s 6mA. The Value of R-2.4kn and the value of Ve 4.8V Vo At which value of l, does the diode turn on O a.2.292 mA b. 1.833 mA c. 2.865 mA O d. 1.467 mA If l = 2.1mA, What is the value of Vo O a. 5.04 V O b. 4.03 V O c 6.3 V O d. 3.23 V If l= 1.6mA, What is the value of lo O a. 1.917 mA b. 0 mA O c 0.639 mA O d. 1.278 mA EO o
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
The cut-in voltage for each diode in the circuits shown in Figure Pl.30 is V, = 0.6 V. For each circuit, determine the diode current I, and the voltage Vo (mea- sured with respect to ground potential). Q7 R= 10 k2 Vo oVo Ip R= 10 k2 5 V 5V 5 V 5 V (a) (b) R= 10 k2 Vo 5V E 5 V (c)