In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 24 kW , when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.6 lag and (ii) 0.906 lag. The total three-phase power remains unchanged. (i) W1 at 0.6 lag (i) W2 at 0.6 lag (ii) W1 at 0.906 lag (ii) W2 at 0.906 lag

In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 24 kW , when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.6 lag and (ii) 0.906 lag. The total three-phase power remains unchanged. (i) W1 at 0.6 lag (i) W2 at 0.6 lag (ii) W1 at 0.906 lag (ii) W2 at 0.906 lag

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Similar questions

1. Why is there a wattmeter reading when the load is purely inductive? 2. Why is there no wattmeter reading when the load is purely capacitive?
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
The voltage-flux adjustment of a certain single phase 220 V induction watthour meter is altered so that the phase angle between the applied voltage and flux due to it 75° instead of this 90°. The error introduced in the reading of this meter when the current is 5 A at unity power factor is O -24.56 W O 37.48 W O 24.56 W O -37.48 W
If a load is leading, which statement is NOT true? a. The load is capacitive. b. It’s reactive power is positive. c. Current ahead of the voltage. d. Its power factor is positive.
1. Find the average power drawn by each charge. Total average power drawn by the loadFind. 2. Find the total average power of the load using the 2 wattmeter method. You find on 1compare with the result.
The regulation of an alternator is likely to be negative in case of resistive load O True O False
1- Which of the following statement is TRUE ? a. True power is measured in VA b. All the power drawn by a resistive circuit is converted to useful work c. Apparent power and Reactive power are always equal d. True power cannot be measured using wattmeter 2- Which of the following statement is TRUE ? a. Bulb is considered as inductive load b. Loads such as transformers and motors consume reactive power with current waveform lagging the voltage c. Loads such as transformers and motors consume power with current waveform leading the voltage d. Heating element is example of capacitive load
Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must be in polar formand should be in 4 decimal places).
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?
A 300 V, 5A, 0.2 pf low power factor wattmeter is used to measure the power consumed by a load. The wattmeter scale has 150 divisions and the pointer is on the 100th division. The power consumed by the load (in Watts) is
A 150-kVA load has a power factor of 0.75 lagging. What is the kVA rating of connected capacitors to be installed in order to improve the over-all power factor of the to 0.91 lagging
Four conductors meet at a junction. the current are i1= 5sinwt, i2= 3sin(wt + 90) and i3= 2sin(wt-90). calculate the rms value of i4.