In an AC to DC rectifier circuit, the output DC signal of the rectified wave was measured to be Vpc= (7.9±0.8)V and its ripple voltage was measured to be Vripple=(0.38±0.01) mV. What is the uncertainty on the quality factor of the rectifier? Divide your value by 1E-6 and report the answer to 2 decimal places.

In an AC to DC rectifier circuit, the output DC signal of the rectified wave was measured to be Vpc= (7.9±0.8)V and its ripple voltage was measured to be Vripple=(0.38±0.01) mV. What is the uncertainty on the quality factor of the rectifier? Divide your value by 1E-6 and report the answer to 2 decimal places.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What will be the out put of the following meters, if an average responding a.c meter of halfwave rectifier read (4.71v), and true form factor of input waveform is (1.414).
Determine the voltage across the resistor, the current in the resistor, and the output voltage in figure 1 and figure 2. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.
Design a controlled half wave rectifier circuit to produce an average of 30 V across a 250 ohm load resistor from a 220 Volt max 50 Hz AC source. Determine the power absorbed by the resistance. What would be the average voltage value if diodes were used in this circuit? no chat GPT, only hand written please otherwise leave a DOWNVOTE
Example 35: A full wave rectifier used 220v , with firing angle 10° ,total resistance load5 K2, inductance 2.34 H,and frequency 60HZ , Draw and calculate: (a) VD.c and ID.c (b) VD.C(Max) (c) Vn (d) Vor.m.s.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Determine the output voltage of a Half-wave rectifier with an input peak-to-peak sinusoidal voltage of Vm.
What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
A full wave bridge rectifier is supplied from 230V, 50Hz and uses a transformer of turns ration 15:1. It uses load resistance of 50 ohms. Calculate load voltage and ripple voltage. Assume ideal diode and transformer. Assume ripple factor equals to 0.482. a.Load Voltage= 13.8 V; Ripple Voltage=6.652 V b.Load Voltage= 15.6 V; Ripple Voltage=7.611 V c.Load Voltage= 21.3 V; Ripple Voltage=8.410 V d.Load Voltage= 25.1 V; Ripple Voltage=10.442 V