in a surface condenser the pressure ofsteam is Q12 bar. The rote of cooling water flow is 40 kgAgof steam condensedCondensate teaves at 44°C and dhe rise in termperature ofcircuiating water is 13°C Determine the dryness fraction ofsteam entering the condenser.

When the temperature of steam is equal to the boiling point at a certain pressure, it is said to be…

in a surface condenser the pressure of stean is Q12 bar. The rote of cooling water flow is 40 kg/kg of steam condensed Condensate leaves at 44C and the rise in termperature of circuiating water is 13°C Determine the dryness fraction of steam entering the condenser.

in a surface condenser the pressure of stean is Q12 bar. The rote of cooling water flow is 40 kg/kg of steam condensed Condensate leaves at 44C and the rise in termperature of circuiating water is 13°C Determine the dryness fraction of steam entering the condenser.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter47: High-pressure, Low-pressure, And Absorption Chilled-water Systems

Section: Chapter Questions

Problem 13RQ: The subcooling temperature in a condenser can be measured by taking the difference between the A....

See similar textbooks

Related questions

Q: In a Parson turbine running at 1500 RPM the available enthalpy drop for expansion is 62.8 kJ/kg. If ...

A: A reaction turbine, also known as a Parsons turbine, is a turbine having moving nozzles that alterna...

Q: üiven- u= 35mls V = om/s t-5secs S-2

Q: Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500...

A: Given:Impeller Diameter, D1=500 mm Discharge Q, 4 m3/s Head= 5395/100=5.395 m RPM, N1=1500 Efficien...

Q: By means of a graph, show the relationship between temperature and density of a substance.

A: Dear student, According to the guidelines I am allowed to answer only one proble...

Q: plss make and introduction about speed control of pneuamtic cylinder and indirect control of cylinde...

A: The pneumatic cylinders can be directly controlled via the actuation of a final directional control ...

Q: . In the casting of steel under certain mould conditions, the mould constant in Chvorinov's rule is ...

A: Given:Mould constant, C=4 min/cm2Dimension of plate=25×8×2.5 cm3n=2

Q: ank the materials from highest to lowest of which has the best thermal shock resistance without doin...

A: Thermal shock resistance refers to a material's capacity to withstand quick and abrupt temperatur...

Q: Water flows through the pipe contraction shown in Figure I. For the given difference in piezometer l...

Q: V. R 6R Liner velocity distribution V. V. V.

A: For Laminar and turbulent flow at center there will be zero velocity because of the stagnation point...

Q: Explain the relationship between the answers for (a) and (b).

A: we have to determine the saturation pressure of liquid water & vapor @ 100 Celcius

Q: enthalpy of 3828 kJ/kg at 70m/s and leaves the same stage with an enthalpy: 2846 kJ/kg and a velocit...

Q: The vacuum in the condenser is 716 mm of Hg when the barometer reads 748 mm of Hg. In another case, ...

A: we raise the pressure to 760 mm without any change in absolute pressure in the condenser

Q: Which of the following statements about vehicles that are subject to Diesel Opacity Emissions (Smoke...

A: According to the terms, all vehicles registered outside DEMA with MGW of 8500 lb will not require an...

Q: ding mome

Q: A flywheel of moment of inertia 9.8kg m3 fluctuates by 30rpm for a fluctuation in energy of 1936 jou...

A: Given data: N1-N2=30 rpmI=9.8 kg.m2E=1936 J Need to determine the mean speed of the flywheel.

Q: Bar CD is rotating counterclockwise with the constant angular velocity of 8.14 radi a-1.79 , b-2.13 ...

Q: An experiment is conducted on the surface of the planet Mars. Assume an isothermal atmosphere, where...

Q: the definition of actual air-fuel ratio?

A: To define what is ctual air-fuel ratio.

Q: Enumerate the steps in cutting a plate using gas cutting (welding).

A: Gas cutting is basically a thermal cutting process in which fuel gas and oxygen are used. The most w...

Q: What is value of specific gravity

A: Specific gravity is the ratio of the density of substance with respect to the water .

Q: An engine undergoes the brake power testing in an brake rope dynamometer running at 8000 rpm and exp...

A: Given data: N=8000 rpmT=500 N.m Need to determine the brake power generated by the engine.

Q: Traveling with an initial speed of vo 53 km/h, a car accelerates at 3,259 km/h along a straight road...

A: Given data : Acceleration=a Initial speed=U Final speed=V To find : Distance

Q: A rigid uniform flywheel has diameter of 1 m. A torque of 20 N-m is applied to the disk. If the disk...

Q: change in internal energy and the heat transferred.

A: Given: Compressive work, W=190 kJ PV^1.3= C To determine: Heat transferred Change in internal energy

Q: 2/75 The weld at O can nupport a maximum of 2500 N of force along each of the n- and 1-directions an...

A: The above given problem is related to the resolution of forces in the parallel and the perpendicular...

Q: The company is interested in expanding its production capability into ceramic based products. You h...

A: Sintering techniques are broadly classified into two types: solid state sintering and liquid pha...

Q: the cross-section through point D Determine the resultant nternal loadınigs in Fig. 2. Assume the re...

Q: Thermal resistance for conduction across a slab is inversely proportional to the thickness of t...

A: Given data To select the correct option.

Q: In the system on the picture the bigger wheel is not moving, the smaller wheel is connected to the ...

Q: The tensile test was conducted with the initial cross section area and initial gage length are 80 mm...

Q: Q.7 A pair of parallel helical gears consists of a 20 teeth pinion mashing with a 40 teeth gear. The...

Q: A container equipped with a resistance heater and a mixer is initially filled with 3.6 kg of saturat...

A: Given Data Mass of saturated water vapour m = 3.6 kg Temperature of saturated water vapour= 120°C F...

Q: (a) The water in a large lake is to be used to generate electricity by the installation of a hydraul...

Q: 9-6. A cam drive is used for a mechanism that drives automated assembly machine. The cam follower mu...

Q: A barometric condenser serves a steam turbine which is exhausting 2720 kg of steam per hour at a pre...

A: The above given question is related to the engineering thermodynamics and to calculate the solution ...

Q: 9. The density of saturated vapor refrigerant -134a is expression in the form p= aT + bT + c, (where...

A: Given data:- T1= -15°C T2 = 60°C P1=164 kpa P2=1683kpa

Q: If the journal bearings at A and B exert only horizontal and vertical forces on the shaft, determine...

Q: knife follower motion interval described below: 1. To raise the valve through 50 mm during 120° rota...

Q: The system shown, Figure P3, is released from rest at time t = 0 with the initial displacement xo = ...

Q: An Actual Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. ...

Q: of the follow ,F=1600 M %3D Groove ball b ic load rating oad factor,

Q: The partial pressure of wale air sample of relative humidity 70% is 1.6 kPa, the total pressure bein...

Q: steum at 2-5 Mpa and 3ou e o tapanded istntrpic to e 4 Mpa and itis then further xpan ded Myporbolic...

Q: A 2.0-kg block slides on a rough, horizontal surface. A force ( P = 6.0 N) is applied to the block a...

Q: 1. You serve a volleyball with a mass of 2.1 kg. The ball leaves your hand with a speed of 30 m's. T...

Q: transfer with air. If the air side heat transf It is proposed to coat a 1 mm diameter wire w enamel ...

A: Given:diameter of wire, d=1 mmradius, r=d2=0.5 mmthermal conductivity, k=0.1 W/m.Kheat transfer coef...

Q: 8. The potential energy of an apple is 6.00 joules. The apple is 3.00-meters high. What is the mass ...

A: Answer: The mass of the apple is 203.8736 grams.

Q: Q.44. Give the different parameters value for different dielectric used in cable. Also, describe the...

A: When an electric field is applied to a dielectric material, electric charges do not flow through...

Q: A simple Rankine cycle works between the boiler pressure of 4 MPa and condenser pressure of 3 kPa. T...

Q: A tennis ball is projected upward with a velocity of 120 m/s. Neglecting air resistance, how long wi...

Concept explainers

Strengthening of Alloys

Strengthening of the alloys is required as metals become weak due to various lattice defects, metal bonding phenomena. The strength of the metals is not enough for any mechanical work. The internal dislocations of any metals arise due to forming processes. Due to the movement of these dislocations, the metals are plastically deformed.

Question

in a surface condenser the pressure of
steam is Q12 bar. The rote of cooling water flow is 40 kgAg
of steam condensed
Condensate teaves at 44°C and dhe rise in termperature of
circuiating water is 13°C Determine the dryness fraction of
steam entering the condenser.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A reheater cycle with two stages of reheating is executed with steam expandinginitially from 20.544 Mpa and 540oC. The pressures of two reheaters are 3.2544 Mpaand 0.85544 Mpa, and the steam leaves each reheater at 540 oC. Condensation occursat 70 oC. Calculate W, ec and ee.
A water temperature rise of 18degF in the water cooled condenser isequivalent in degC to: ?the asnwer is 10 but dont know the solution pls help.
Example: 100 TR refrigeration capacity of air condition plant using R134a has evaporating and condensing temperature of 0°C and 35°C respectively, the refrigerant enters with degree of super heat of 7°C. Find 1- Dryness fraction of the vapour entering the evaporato. 2- The mass flow rate of refrigerant, and 3- COP of the system
A reheater cycle with two stages of reheating is executed with steam expandinginitially from 20.547 Mpa and 540 oC. The pressures of two reheaters are 3.2547 Mpaand 0.85547 Mpa, and the steam leaves each reheater at 540oC. Condensation occurs at 70oC. Calculate W, ec and ee. Put state 1, 2 and so on, the cycle analysis. Make it clear format.
What should be the percent increase of COPof a standard vapor compression refrigerationsystem when expansion of R-12 is isentropicinstead of isenthalpic process? Evaporator andcondenser temperature limits are -10°C and30°C respectively.
A reheater cycle is executed of 1 kg steam expanding initially from 12.546 Mpa and540.546oC. The reheater pressures are 2.546 Mpa and the steam leaves the reheaterat 420.546oC. Condensation occurs at 0.02546 Mpa. Calculate W, ec and ee. Ps, please put where the state 1,2 and so on. Make it clear and understandable thank you.
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
The air outside is 40 C and 60% r.h. I want torun an air conditioner to cool it to 15 C. The deliver rate should be 1000 m^3/min. What is Q and the rate at which water condenses (if any)?
Natural gas boiler with power otput 10 kW operate with efficiency 90% without flue gas condensation.Please advice reduction of gas consumption in nm3/s if heat of condensation will be completely used for heating.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Does R134a suitable refrigerant in Cryogenic plant for liquid oxygen produduction? Explain, if not what did you recomment? R401A has been phased out.
Determine the Condenser heat disc'ipation require ment in MW, C megawatt thermal) for coal fired 1000 MWe power plant with thermal effiiency, of 40% and release 15% of the heat f urnace. produced in the