In a slider-crank mechanism, the crank is 480 mm long and rotates at 20 rad/s in the counter-clockwise direction The length of the connecting rod is 1.6 m. When the crank turns 60° from the inner-dead centre, determine the (i) velocity of the slider (ii) velocity of a point E located at a distance 450 mm on the connecting rod extended E Example 2.2 A 60° (a) F B TTTTT G (iii) position and velocity of a point F on the connecting rod having the least absolute velocity (iv) angular velocity of the connecting rod (v) velocities of rubbing at the pins of the crankshaft, crank and the cross-head having diameters 80, 60 and 100 mm respectively.

In a slider-crank mechanism, the crank is 480 mm long and rotates at 20 rad/s in the counter-clockwise direction The length of the connecting rod is 1.6 m. When the crank turns 60° from the inner-dead centre, determine the (i) velocity of the slider (ii) velocity of a point E located at a distance 450 mm on the connecting rod extended E Example 2.2 A 60° (a) F B TTTTT G (iii) position and velocity of a point F on the connecting rod having the least absolute velocity (iv) angular velocity of the connecting rod (v) velocities of rubbing at the pins of the crankshaft, crank and the cross-head having diameters 80, 60 and 100 mm respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To be able to develop an equation relating the linear distance between moving bodies to the angular position and velocity of the first or driving body and to use this relationship to derive the function for absolute velocity and acceleration of the second body. A circular cam is in contact with a rectangular lifter and used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 5.0 in and is rotating about point O, which is offset from the center by a distance c = 2.7 in. The cam’s angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. The lifter with respect to point O when the angle is θ = 25 ∘, the angular velocity is ω = 3.4 rad/s, and the angular acceleration is α = 3.0 rad/s2 . Find the range of…
To be able to develop an equation relating the linear distance between moving bodies to the angular position and velocity of the first or driving body and to use this relationship to derive the function for absolute velocity and acceleration of the second body. A circular cam is in contact with a rectangular lifter and used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 5.0 in and is rotating about point O, which is offset from the center by a distance c = 2.7 in. The cam’s angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. Find the linear velocity of the lifter with respect to point O when the cam has an angular position of θ = 25 ∘ and is rotating with an angular velocity of ω = 3.4 rad/s…
3. The 40.64 cm. diameter pulley of a gasoline engine is connected by a belt (which is assumed not to slip) to the pulley of the pump. The belt speed is 1200 m. / min. Determine (1) the angular speed of the engine pulley in RPM and in rad / sec. and the diameter in cm. of the pump pulley if the pump speed is one-half the speed of the engine pulley.
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
Home wnk #1 19. Prohlem te 3 in/sec 25" 30 in B a rod is attached do tvs slidere moing in yenida bara by faité reniversal as shorun inthe figue Frind Ahe relo eily of slider B when shider A height of shding down to at. 25" and is wilh a speed of 3 i.
3. The crank, connecting rod and cross head of a stationary steam engine are shown diagrammatically in fig. The 22.5 cm crank arm BC is rotating at a constant rate of 150 rpm. The length of the connecting rod AB is 80 cm. Find the velocity and acceleration of the cross-head A when 0=45º. The cross-head moves on a horizontal line through C.
2- (kinematics) The crank, connecting rod and cross head of a stationary steam engine are shown diagrammatically in fig. The 22.5 cm crank arm BC is rotating at a constant rate of 150 rpm. The length of the connecting rod AB is 80 cm. Find the velocity and acceleration of the cross-head A when 0-450. The cross-head moves on a horizontal line through C.
2- (kinematics) The crank, connecting rod and cross head of a stationary steam engine are shown diagrammatically in fig. The 22.5 cm crank arm BC is rotating at a constant rate of 150 rpm. The length of the connecting rod AB is 80 cm. Find the velocity and acceleration of the cross-head A when 0=45°. The cross-head moves on a horizontal line through C. 16 C D.
1.Locate all of the instant centers in the mechanism shown below. If link 2 is tuming CW at the rate of 60 rad/s, determine the linear velocity of points C and E using instant centers. AD 3.8" AB 1.2" BC = 3.0" CD 2.3" CE = 1.35" EB 2.05" %3D %3D %3! B 125
The crank of a slider crank mechanism rotates clockwise at a constant speed of 300 rpm. The crank is 150 mm and the connecting rod is 600 mm long. Determine : (i) linear velocity of the mid-point of the connecting rod
Rod AB rotates counterclockwise with a constant angular velocity w=2 rad/s. The collar consists of two pin-connected slider blocks which are constrained to move along the circular path and the rod AB. Suppose that r=0.4 m. (Figure 1) Figure 1 of 1 B O Y Y Part A Determine the magnitude of velocity of point C located on the double collar when 0-30°. Express your answer to three significant figures and include the appropriate units. Vc = HA Part B Value Submit Request Answer DEK Units Determine the direction of velocity of point C located on the double collar measured counterclockwise from the positive z axis when 0-30
In a slider crank mechanism, the crank is 60 mm long and connection rod 240 mm long. When the crank has moved through 40° from the Inner dear centre position, the velocity of slider is 3 m/s. Find (i) Angular acceleration of connecting rod.