In a cathode-ray tube (CRT), an electron travels in a vacuum and enters a region between two "deflection" plates which have equal and opposite charges. The dimensions of each plate are L = 12 cm by d = 5 cm, and the gap between them is h = 2.5 mm. (Note: the diagram is not drawn to scale and the direction of the electric field may not be correct, depending on your randomization.) During a 0.001 s interval while it is between the plates, the change of the momentum of the electron ΔP is < 0, 9.60e-17, 0 > kg m/s.What is the electric field between the plates?

In a cathode-ray tube (CRT), an electron travels in a vacuum and enters a region between two "deflection" plates which have equal and opposite charges. The dimensions of each plate are L = 12 cm by d = 5 cm, and the gap between them is h = 2.5 mm. (Note: the diagram is not drawn to scale and the direction of the electric field may not be correct, depending on your randomization.) During a 0.001 s interval while it is between the plates, the change of the momentum of the electron ΔP is < 0, 9.60e-17, 0 > kg m/s.What is the electric field between the plates?

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter43: Nuclear Physics

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An electron is fired at a speed vi = 4.3 × 106 m/s and at an angle θi = 39.7° between two parallel conducting plates as shown in the figure. If s = 1.7 mm and the voltage difference between the plates is ΔV = 99.8 V, determine how close, w, the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer. Do not include units. The x-axis of the coordinate system is in the middle of the parallel plate capacitor. Round your answer to 6 decimal places.
An electron is fired at a speed vi = 4.1 × 106 m/s and at an angle θi = 38.2° between two parallel conducting plates as shown in the figure. If s = 1.9 mm and the voltage difference between the plates is ΔV = 98.3 V, determine how close, w, the electron will get to the bottom plate. Put your answer in meters and include at 6 decimal places in your answer.
A simple and common technique for accelerating electrons is shown in the figure, which depicts a uniform electric field between two plates. Electrons are released, usually from a hot filament, near the negative plate, and there is a small hole in the positive plate that allows the electrons to pass through. Randomized Variables E = 2.7 × 104 N/C Calculate the horizontal component of the electron's acceleration if the field strength is 2.7 × 104 N/C. Express your answer in meters per second squared, and assume the electric field is pointing in the negative x-direction as shown in the figure.
Fig.2
Problem 2: Consider the parallel-plate capacitor shown in the figure. The plate separation is 5.9 mm and the the electric field inside is 24 N/C. An electron is positioned halfway between the plates and is given some initial velocity, v₁. Randomized Variables d = 5.9 mm E = 24 N/C + + + + + + + + d Otheexpertta.com Part (a) What speed, in meters per second, must the electron have in order to make it to the negatively charged plate? Part (b) If the electron has half the speed needed to reach the negative plate, it will turn around and go towards the positive plate. What will its speed be, in meters per second, when it reaches the positive plate in this case? select part Vf,b=1
The figure (Fig. 1) shows a long cylindrical capacitor consists of a solid conducting core with radius r1=9mm and outer hollow conducting tube with an inner radius of r2=35mm. The length of the capacitor is L=28cm. Figure 2 is the cross sectional view of the system. This system of rod and shell is connected to a voltage source of emf E=6.8volts. There is no dielectric material present in the system as of now. a) Calculate the capacitance of the capacitor b) Say the inner rod is negatively charged. Given this, calculate the charge density of the outer surface. And show how the electric field lines are oriented in this system. Hint: you can use the cross section for this (Fig. 2).
The figure (Fig. 1) shows a long cylindrical capacitor consists of a solid conducting core with radius r1=7mm and outer hollow conducting tube with an inner radius of r2=29mm . The length of the capacitor is L=32cm . Figure 2 is the cross sectional view of the system. This system of rod and shell is connected to a voltage source of emf E=6.4volts . There is no dielectric material present in the system as of now.
Consider electrons flowing in copper. a) Compute the average time between collisions for free electrons in copper. (Hint: The density of free electrons in copper is 8.44 x 1028 electrons / m3). b) Due to quantum mechanical effects, electrons in copper have a speed of about 106 m/s at room temperature. Show that electrons moving at such speeds will travel an average distance of 25 nanometers between collisions.
Consider the oscillations of an electron in a plasma of electrons. let N be the number of electrons per cubic meter. Calculate the oscillation frequency v, in Hz O 17.96 N O 2.25 N O 8.98 N O 4.49 N O 13.47/N
An evacuated tube uses an accelerating voltage of 26.026.0-kV to accelerate electrons to hit a copper plate and produce x-rays. Non-relativistically, what would be the maximum speed of these electrons? Enter your answer to 3 sigfigs in the coefficient and in calculator notation. Ex: 3.00E8. This problem required units.
Fig.2
For analyzing the relationship between electrode radii and electric field in an electrode system (not necessarily concentric spheres), the graph of change in Emax with respect to ri is obtained as shown in the figure. Suppose that the effective electrode separation varies as a = r,(2 – In(r,)). Considering electric field strength of Es=50 kV/cm . a) Find the range of ri to have partial discharge. b) Find the range of rị to have total breakdown. c) Sketch the graph of change in Umax With respect to r; and specify the breakdown behavior in different regions by considering U=100 kV. * 100 90 80 70 60 50 40 30 20 10 rl (cm) r2=7 Optimum Geometric Char. Emax (rl) kV/cm