If we consider the above timing, how many stalls would be needed if we want to overcome the data hazard using Stalls and code scheduling? For executing One Iw instruction, how much longer will it take to execute the instruction with 5 stage pipelining compared to single cycle datapath? (only write the value, don't need to mention unit) If we want to execute 395 consecutive sll instructions with 5 stage pipelining what will be the total duration of execution (without any hazards)?

If we consider the above timing, how many stalls would be needed if we want to overcome the data hazard using Stalls and code scheduling? For executing One Iw instruction, how much longer will it take to execute the instruction with 5 stage pipelining compared to single cycle datapath? (only write the value, don't need to mention unit) If we want to execute 395 consecutive sll instructions with 5 stage pipelining what will be the total duration of execution (without any hazards)?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In this setup, data for each instruction is obtained independently of how data for other instructions is obtained. When we need a(n): A Instructions/Data Sets That Vary B A Variety of Information and Directions in a C Format Exclusive Information Straight D Incident Several Insts From a Single Infusion
What is the hex representation of the given RISC-V instruction? Note: just translate the beq instruction beq x7, x7, loop inst ... 1 inst ... inst ... 3 inst ... 4 inst ... 5 2 loop: assume loop is 6 instructions away from beq. beq x19, x10, offset = 16 bytes 13-bit immediate, imm[12:0], with value 16 Op00000010000 imm[0] discarded, always zero imm[12] 0 000000 01010 | 10011 imm[11] |1000 0 1100011 BEQ imm[4:1] 000 imm[10:5] rs2=10 rs1=19 BRANCH
What would happen if an instruction was disobeyed, and why would that be the case? In the following scenarios, a TLB that is maintained by software is more efficient than one that is handled by hardware:
For the problems in this exercise, assume that there are no pipeline stalls and that the breakdown of executed instructions is as follows: add addi not beq lw sw 20% 20% 0% 25% 25% 10% In what fraction of all cycles is the data memory used?In what fraction of all cycles is the input of the sign-extend circuit needed? What is this circuit doing in cycles in which its input is not needed?
What is the main issue of a single data path design? Need multiple Multiplexors. Longest delay determines clock period. Does not support JUMP instruction. Each datapath element can only do one function at a time.
The system writes to VA page 30 if an instruction is not accepted; what does it mean? Compared to a TLB handled by hardware, a TLB controlled by software would be quicker in the following cases:
What is the energy consumption of the worst-case MIPS instruction, and how much energy is required to execute it?
Do you know what would happen if an instruction was rejected? When compared to a hardware-managed TLB, a software-managed TLB is quicker in the following scenarios:
The "Add immediate unsigned" MIPS instruction: addi Rt, Rs, Imm requires the immediate field to be extended from 16 bits to 32 bits. If the value of the immediate field is: 1111000011110000 what will be the sign extended value of this field from 16 bits to 32 bits? Choose the best answer. 01111111111111111111000011110000 O 11111111111111111111000011110000 O This is a trick question. You cannot sign extend a negative number O 00000000000000001111000011110000 10000000000000001111000011110000 This is a trick question. You cannot sign extend a positive number
If an instruction is not accepted and it writes to VA page 30, what will happen? A TLB that is handled by software would perform better than a TLB that is controlled by hardware in the following situations:
Which of the following conditional transfer instructions? Select one: Oa. JZ L O b. JMP L C. CALL O d. CMP
What happens if an instruction writes to VA page 30 without being approved? A software-managed TLB would be quicker than a hardware-managed TLB in the following situations: