If water is pumped from reservoir 1 to reservoir 2through a 20 cm pipe with a length L1=70 m, andflow rate of 150 L/s, determine the pump power.-6' 2(take kinematic viscosity= 1.3 10 m/s, Ks=0.02mm)Elevation =35 mElevation = 15 mL1.40 m-Select one:a. 46.32 kWb. 45.13 kWc. 43.93 kWd. 41.55 kW

The expression for velocity in pipe is given as V=QA Substitute the value in above expression V=0.15…

If water is pumped from reservoir 1 to reservoir 2 through a 20 cm pipe with a length L1=70 m, and flow rate of 150 L/s, determine the pump power. (take kinematic viscosity= 1.3 10°m /s, Ks=0.02 -6 2 mm)

If water is pumped from reservoir 1 to reservoir 2 through a 20 cm pipe with a length L1=70 m, and flow rate of 150 L/s, determine the pump power. (take kinematic viscosity= 1.3 10°m /s, Ks=0.02 -6 2 mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: From a deep well, water is being pump through a 250mm pipe, 400m long into an elevated tank. If the…

A: Given, D = 250 mm or 0.25 m L = 400 m f = 0.02

Q: A large tank open to the atmosphere is filled with water to a height of 9.3 m from the outlet tap. A…

A: Discharge through the mouth piece= Q=Cd a2gH Velocity = Q/a= Cd2gH= 0.7072*9.81*9.3= 9.55 m/s So the…

Q: A discharge well that completely penetrates a confined aquifer has radius 0.5 m. The steadystate…

Q: Determine the pressure head at point 1 and point 2 (in meters). Also, determine the power delivered…

Q: A 150-mm diameter penstock supplies water to a turbine under a constant head of 30 meters. Calculate…

Q: Water backs up behind a concrete dam as shown in the figure. Leakage under the foundation gives a…

Q: Water flows from an upper reservoir to a lower one while passing a turbine as shown. 1. Compute the…

Q: 3. If the flow rate through a 10 cm-diameter wrought iron pipe is 0.04 m/s as shown in figure below,…

Q: Water flow in a pipe of diameter 600mm having a length of 2200 m at a velocity of 2m/s. At the end…

Q: Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe…

Q: Consider the two reservoirs shown in the figure, connected by a single pipe that changes diameter…

Q: Reservoir 1 = In figure, if L1= 20 m, diameter 30 cm, velocity = 0.1 m/s, friction ?= factor= 0.023,…

Q: 10.67 In a rectangular channel 4 m wide flow of 7.65 m/s the depth is 0.4 m. If a hydraulic jump is…

A: We have equation2q2g=y1y2y1+y2

Q: Water is pumped from a lake surface through an 8-in pipe at a rate of 10 ft3/s. If viscous effects…

A: Given : Dia of pipe - 8inches Discharge - 10 ft3/s Elevation above the lake - 6ft To find - Pressure…

Q: A 2.5-m square vertical tank 4 m high contains 3.5 m of oil (SG-0.82). A 100 mm diameter circular…

Q: Problem 1. A water reservoir with dimensions of 10 x 10 × 10 m is connected to 3 pipes. Water is…

A: Given data: Dimension of the reservoir =(10 x 10 x 10)m water density = 1000 kg/m3 (Assumed) v1…

Q: A 20 cm diameter well penetrates an Artesian aquifer, 35 m thick. The discharge from this well for a…

A: Given that,

Q: 10. Water is flowing in a straight 150 mm diameter, high density polyethylene (HDPE) pipe installed…

Q: T530 m-150 me. C » 130 C ;=120 I830 m-300 mm, C, » 130 250 mm__ El. 0.0 1220 m-250 mm C C; = 120

A: The given information is The pressure head at A is 3.05 m The pressure head at B is 89.9m The…

Q: A pump draws water from reservoir A and lifts to reservoir B. Points 1 and 2 are points just before…

A: Given, Discharge, say Q = 15 L/s = 0.015 m3/s [1 m3 = 1000 L] Diameter of pipe at 1, D1 = 150 mm =…

Q: 2. Water (µ = 1.138x10³ kg/m-s) is flowing steadily in a 30m long and 4cm diameter horizontal pipe…

Q: The performance data of a water pump follow the curve fit Havailable = HO = aV^2, where the pump's…

Q: Consider the flow of water in a 10-m wide channel at a rate of 70 m3 /s and a flow depth of 0.5 m.…

A: Using formula

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure below. The loss…

A: Output power through the pump will be calculated by applying the energy equation between point A and…

Q: Shown in figure, A pump discharged 0.05 cu. m/sec. water from a 220 mm suction pipe and delivers it…

Q: 9. The depth of flow of water at a section of a rectangular channel of width 2 m is 0.3 m. The…

A: Given data, Width of rectangular channel b = 2 m Depth of channel y = 0.3 m Discharge through the…

Q: Q2: Water is flow by a rate = (V(0.3( still stable due to using a pump as shown in figure below. A…

A: Discharge is the main quantity in any sector that is used to transfer fluid from one place to…

Q: Water flows through the turbine shown at a rate of 0.386 m3/s. The pressures at points A and B are…

Q: Neglecting losses, calculate V2 (ms) of water existing the nazzle D1 = 10 cm D2 = 2.5 cm P1 = 1600…

A: Given: The diameter D1 is 10 cm. The diameter D2 is 2.5 cm. The pressure P1 is 1600 kPa. The…

Q: Compute for the flow rate in cubic meter per second of oil with p = 950 kg/m³ and v = 0.00002 m?/s,…

Q: A motor-driven centrifugal pump delivers 15°C water at the rate of 10 m³/min from a reservoir,…

A: T = Temperature of water = 15°CQ = Rate of flow = 10 m3/min = 1060 = 0.1667 m3/secL = Length of pipe…

Q: Q3 a) Water flows at the rate of 900 L min from the reservoir and through the pipe shown in Figure.…

Q: Q.5.Calculate the stability of the intake box structure for water treatment plant with dimensions…

A: Given, Box structure water treatment plant dimension = 5*5*10 m Flooded chamber dimensions = 4*4*10…

Q: Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoir at elevation 70 m.…

Q: Water at 10⁰C flows at the rate of 900 L/min from the reservoir and through the pipe shown in the…

Q: Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm…

A: Options given for subpart a and b are not correct. If we take hf1 = 80 then the answers are…

Q: 8) Estimate the height to which water will rise in a capillary tube of diameter 3mm. Use o =0.0728…

Q: The water tank is connected with a pipe ( Diameter= 5-cm) as shown below. Find the horse power of a…

A: The pump is the device that helps to transmit the water from lower level to higher or to another…

Q: An le Volve Pump open P=150 kPa Water sprotruding entrance

A: Given data in question Diameter of pipe Density of water Dynamic viscosity of water Length of pipe…

Q: A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev = 20m) into open air (Point…

A: To find :- Velocity in the siphon in m/s

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m/s. If…

Q: Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm…

A: The answers given for subpart (a) and (b) are not correct.

Q: Determine the water power, pump power and motor load for a pump system designed to deliver 2.07…

A: Water power : It is the power of water where kinetic energy of water is converted in form of…

Q: Reservoirs A and B have elevations 250 m and 100 m respectively, which are connected by a pipe…

Q: A centrifugal water pump is tested under its design flow rate Q=250 m/hr. The static pressure at the…

A: Given Discharge Q=250 m3/hr=0.0694 m3/secpressure P1=1.2 bar=120 KPaand at outlet end P2=8.5…

Q: Water (p =1000 kg/m , p=1.59×103 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth…

A: i. The diameter of pipe is 1 cm = 0.01 m initially and then changed to 1 m. So it is the case of…

Q: Q: In a rough pipe of diameter 500mm and length 3500m, water is flowing at the rate of 0.5 m'/s. If…

Q: A 1,200-mm diameter transmission pipe carries 126 1/s from an elevated storage tank open to…

A: Given diameter of pipe = 1200 mm Water surface elevation of reservoir = 540m pipe length under…

Q: Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe…

A: Given information: Water is flowing in a pipe at the pressure=PF=102400 MPa Water is flowing in a…

Q: An open top cylindrical tank, 4 m high and 2 m Øfloats in water with a draft of 2.5 m. compute the…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

If water is pumped from reservoir 1 to reservoir 2
through a 20 cm pipe with a length L1=70 m, and
flow rate of 150 L/s, determine the pump power.
-6' 2
(take kinematic viscosity= 1.3 10 m/s, Ks=0.02
mm)
Elevation =35 m
Elevation = 15 m
L1
.40 m-
Select one:
a. 46.32 kW
b. 45.13 kW
c. 43.93 kW
d. 41.55 kW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Reservoir B in the figure receives 0.06 m³/s of flow. Determine the flow in line DC. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m2/s Decimal Places required in the final answer: 3 El 100m A B 1500 m, 450 mm, f= 0.0225 El 82m 500 m, 250 mm f= 0.0178 D 750 m, 300 mm, f 0.0168
(Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node, D. Assume elevation at Node, D to be 328 feet and friction factor, f, of 0.02 for all pipes. [NOTE: This is a three-part problem]. A B Elevation (ft) Length (ft) 19,680 Diameter (ft) Reservoir Pipe Part A) A 656 AD 3.28 В 590 BD 13,120 2.5 558 CD 29,520 2.5 19,680 13,120 Part B) A 656 AD 3.28 В 574 BD 3.28 CD 29,520 19,680 19,680 492 2.5 Part C) A 656 AD 3.28 В 590 BD 3.28 492 CD 19,680 3.28
Q2- Water ( p= 990 kg/m' & µ= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft cubed with a discharge pressure of 150 psig. Suction pressure indicates a 2 HG vacuum. The diameter of the suction and the discharge are 5 in. and 4 in. respectively. The pump has an efficiency of 70% while the motor efficiency is 80%. Determine the (a) water horsepower of the pump (b) bhp of pump motor (c) power input to drive the motor.
Typical capillary viscometer (2) The tank below is cylindrical with a diameter of 10 m . The outlet is a cylindrical frictionless nozzle, with a diameter 1 m. The top of the tank is open to the atmosphere. Page | 1 When the level in the tank is 10 m above the centerline of the outlet, how fast is the level in the tank falling? woun 10 m 10 m Im
A 10-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold the nozzle on the hose. O 2728 N O5861 N Water: 1000 kg/m³ O 3566 N O 4067 N D₁ = 10 cm Pa = 0 (gage) Hint: One-dimensional momentum flux: F = ploutvout - Plin Vin (2) D₂ = 3 cm CV
Consider the section of water distribution piping shown below. Ignoring minor losses, find the flow rate in pipe CB, the total energy at point C, and the pressure at point D. The water temperature is 10°C. C-D: 400m @ 325mm ø D-B: 400m @ 325mm (C=140,k, =1.5x106 m) (C=140,k=1.5x10“ m) Demand = 0.78m³/s C D ZD= 50m Ев 80m zc=45m ZB= 40m A-B: 3000m @ 400mm ở E = 141m (C=120, k =5.3x10+ m) ZA = 60m Flow rate in pipe CB (in m3/s)? Total energy at C (in m)? Pressure at D (kPa)? A-C: 2200m @500mm (C=120, k =5.3x10+ m)
1.) For the water shooting out of the pipe and nozzle under the condition showed, find the height above the nozzle to which the water jet will "shoot". Assume negligible head loss. Water 1.100m 1 ORECA DE Nozzle D-100 mm Point A D-200 mm Pa- 55.0 hPa
(67) The water tank shown is filled by pumping water from the well where the water level is located 9 feet below the elevation of the pump. The head added by the pump at a flow rate of 200 gpm is 27 feet. The efficiency of the pump is 85%. The pump power (hp) is most nearly: A. 1.0 В. 1.5 C. 2.0 Tank D. 2.5 15 ft. Pump 9 ft. Well
Q5: As shown in figure (5). What is the water horsepower of the pump? The pipes characteristics are as follows. Pipe 1 2 3 EL.0.0m D (mm) 200 300 250 L (m) 900 300 1500 0.135 m²/sec f 0.023 0.018 0.02 EL 120m EL.30m
1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft