QUESTION 8If the net, external force acting on a body is zero, thena. The body is accelerating at a small rate.b. The body must be at rest.c. The body must be at rest or moving at a constant velocity.d. The body is not in equilibrium.e. The body must have a uniform density.

We know that Force = mass x acceleration In this question it is given that net external force is…

If the net, external force acting on a body is zero, then a. The body is accelerating at a small rate. b. The body must be at rest. O c. The body must be at rest or moving at a constant velocity. d. The body is not in equilibrium. O e. The body must have a uniform density.

If the net, external force acting on a body is zero, then a. The body is accelerating at a small rate. b. The body must be at rest. O c. The body must be at rest or moving at a constant velocity. d. The body is not in equilibrium. O e. The body must have a uniform density.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter5: The Laws Of Motion

Section: Chapter Questions

Problem 5.9OQ: A truck loaded with sand accelerates along a highway. The driving force on the truck remains...

See similar textbooks

Similar questions

A 9.00-kg object starting from rest falls through a viscous medium and experiences a resistive force given by Equation 6.2. The object reaches one half its terminal speed in 5.54 s. (a) Determine the terminal speed. (b) At what time is the speed of the object three-fourths the terminal speed? (c) How far has the object traveled in the first 5.54 s of motion?
A truck loaded with sand accelerates along a highway. The driving force on the truck remains constant. What happens to the acceleration of the truck if its trailer leaks sand at a constant rate through a hole in its bottom? (a) It decreases at a steady rate. (b) It increases at a steady rate. (c) It increases and then decreases. (d) It decreases and then increases. (e) It remains constant.
A steel ball is dropped onto a hard floor from a height of 1.50 m and rebounds to a height of 1.45 m. (a) Calculate its velocity just before it strikes the floor. (b) Calculate its velocity just after it leaves the floor on its way back up. (c) Calculate its acceleration during contact with the floor if that contact lasts (8.00105s). (d) How much did the ball compress during its collision with the floor, assuming the floor is absolutely rigid?
A person stands on a scale in an elevator. As the elevator starts, the scale has a constant reading of 591 N. As the elevator later stops, the scale reading is 391 N. Assuming the magnitude of the acceleration is the same during starting and stopping, determine (a) the weight of the person, (b) the persons mass, and (c) the acceleration of the elevator.
A soft tennis ball is dropped onto a hard floor from a height of 1.50 m and rebounds to a height of 1.10 m. (a) Calculate its velocity just before it strikes the floor. (b) Calculate its velocity just after it leaves the floor on its way back up. (c) Calculate its acceleration during contact with the floor if that contact lasts (3.50103s). (d) How much did the ball compress during its collision with the floor, assuming the floor is absolutely rigid?
A freight train consists of two 8.00105 -kg engines and 45 cars with average masses of 5.50105 kg. (a) What force must each engine exert backward on the track to accelerate the train at a rate of 5.00102 m/s2 if the force of friction is 7.50105 N, assuming the engines exert identical forces? This is not a large frictional force for such a massive system. Rolling friction for trains is small, and consequently trains are very energy-efficient transportation systems. (b) What is the magnitude of the force in the coupling between the 37th and 38th cars (this is the force each exerts on the other), assuming all cars have the same mass and that friction is evenly distributed among all of the cars and engines?
A 15.0-lb block rests on a horizontal floor, (a) What force does the floor exert on the block? (b) A rope is tied to the block and is run vertically over a pulley. The other end is attached to a free-hanging 10.0-lb object. What now is the force exerted by the floor on the 15.0-lb block? (c) If the 10.0-lb object in part (b) is replaced with a 20.0-lb object, what is the force exerted by the floor on the 15.0-lb block?
Review. A rifle bullet with a mass of 12.0 g traveling toward the right at 260 m/s strikes a large hag of sand and penetrates it to a depth of 23.0 cm. Determine the magnitude and direction of the friction force (assumed constant) that acts on the bullet.
A car is stuck in the mud. A tow truck pulls on the car with the arrangement shown in Figure P5.24. The tow cable is under a tension of 2 500 N and pulls downward and to the left on the pin at its upper end. The light pin is held in equilibrium by forces exerted by the two bars A and B. Each bar is a strut; that is, each is a bar whose weight is small compared to the forces it exerts and which exerts forces only through hinge pins at its ends. Each strut exerts a force directed parallel to its length. Determine the force of tension or compression in each strut. Proceed as follows. Make a guess as to which way (pushing or pulling) each force acts on the top pin. Draw a free-body diagram of the pin. Use the condition for equilibrium of the pin to translate the free-body diagram into equations. From the equations calculate the forces exerted by struts A and B. If you obtain a positive answer, you correctly guessed the direction of the force. A negative answer means that the direction should be reversed, but the absolute value correctly gives the magnitude of the force. If a strut pulls on a pin. it is in tension. If it pushes, the strut is in compression. Identify whether each strut is in tension or in compression.
Consider a large truck carrying a heavy load, such as steel beams. A significant hazard for the driver is that the load may slide forward, crushing the cab, if the truck stops suddenly in an accident or even in braking. Assume, for example, a 10 000-kg load sits on the flatbed of a 20 000-kg truck moving at 12.0 m/s. Assume the load is not tied down to the truck and has a coefficient of static friction of 0.500 with the truck bed. (a) Calculate the minimum stopping distance for which the load will not slide forward relative to the truck. (b) Is any piece of data unnecessary for the solution?
An iron bolt of mass 65.0 g hangs from a string 35.7 cm long. The top end of the string is fixed. Without touching it, a magnet attracts the bolt so that it remains stationary, but is displaced horizontally 28.0 cm to the tight from the previously vertical line of the string. The magnet is located to the right of the bolt and on the same vertical level as the bolt in the final configuration. (a) Draw a free-body diagram of the bolt. (b) Find the tension in the string, (c) Find the magnetic force on the bolt.
A horse is harnessed to a sled having a mass of 236 kg, including supplies. The horse must exert a force exceeding 1 240 N at an angle of 35.0 in order to get the sled moving. Treat the sled as a point particle, (a) Calculate the normal force on the sled when the magnitude of the applied force is 1 240 N. (b) Find the coefficient of static friction between the sled and the ground beneath it. (c) Find the static friction force when the horse is exerting a force of 6.20 102 N on the sled at the same angle.