If the collar P is given a constant acceleration a 1.5g to the right, the pendulum will assume a steady-state deflection @-23 Determine the stiffness kr of the torsional spring which will allow this to happen. The torsional spring is undeformed when the pendulum is in the vertical position. Set m-3.3 kg and L = 920 mm. m T m Answer: ky i Nem/rad

If the collar P is given a constant acceleration a 1.5g to the right, the pendulum will assume a steady-state deflection @-23 Determine the stiffness kr of the torsional spring which will allow this to happen. The torsional spring is undeformed when the pendulum is in the vertical position. Set m-3.3 kg and L = 920 mm. m T m Answer: ky i Nem/rad

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.69P: The collar bearing carries the axial load P = 400 N. Assuming uniform pressure between the collar...

See similar textbooks

Similar questions

A spring with squared and ground ends has 16 active coils diameter of 6 mm and pitch of 10 mm . If spring rate is 85 KN/m , determine the solid force?
2. Find the horizontal force P to start the motion of any part of the system of three blocks resting upon one another as shown. The weight of the blocks are W-300 KN, Ws= 100 KN and Wc =200 KN. Between A and B μ=0.30, between C and B, μ =0.20 and between C and the ground, p=0.10. 1 sni brod nog 02.0-4 B C 05.0-4 Solution: tamos quoy worla bre sosia asquar 005 300 en of jells400 N₁-300 F3 N-300- N₂=300 Assuming B and C will not move. F₁ = 300 (0.30) F₁ = 90 kN ne à bns A zelboß 1 P = 90 kN es ensla berb hebnu 02.0- y elin 05.0= q V in Celpris orllanimetsa MX 008 Assuming C will not move: al 1st F2=400 (0.20) = 80 kN OTE Bm ribirte F₂ vica Assuming the three blocks move: F3 = 0.10 (600) F3 = 60 kN P=60 KN Least force is 60 kN.
(b) Compute the work Ui-2 exerted on the that disk shown undergoes displacement of s = 0.3 m without The spring is initially slipping. unstretched. k = 200 N/m and M = 120 s = 0.3m N-m. k G wwwm- (0.2 m
The 20kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be compressed prior to being slipped into place at point A. If the modulus of the spring is k=2KN/m, what must be its undeformed length?
Exercise 2: Determine the unextended length (l_0) of spring AC, if a force P = 80 lb generates the angle θ = 60 ° for the equilibrium position. Rope AB is 2 feet long. Consider the spring deformation constant as k = 50 lb / ft. Solve this problem using GeoGebra
1- Determine equilibrium the angle 9 for and investigate the stability of the mechanism in this position. The spring has a stiffness of k = 1.5 kN/m and is unstretched when 8 = 90°. The block A has a mass of 40 kg as shown in Fig.1. Neglect the mass of the links. quin 450 mm
The 18-lb box shown is attached to a spring that has a k=2 lb/in and an unstretched length of 14 inches. As shown the spring is stretched to a length of 20 inches. Solve for the unknown force P needed to keep the block in equilibrium. What is the normal force on the block? Assume the surface is smooth. (Note, "smooth" tells you friction is small enough to be neglected.) 20" TTTTTT P
The spring of constant k is unstretched when θ = 0 . Derive an expression for the force P required to deflect the system to an angle θ. The mass of the bars is negligible.
A force of P = 20 N is applied to the cable, which causes the 175-kg reel to turn without slipping on the two rollers A and B of the dispenser. Neglect the mass of the cable. Each roller can be considered as an 18-kg cylinder, having a radius of 0.1 m. The radius of gyration of the reel about its center axis is kg = 0.42 m. (Figure 1) Figure 30% 250 mm OG 500 mm A o OB 400 mm-
The circular bar shown in the figure is vertical.fixed by the support at point A in the plane. AThe spring constant connected to the support is k = 40 N/m. Broadcastingundeformed length, arc between circle ABis the distance. C fitting (bracelet) with a mass of 200 grams,connected to the spring and move in a frictionless circle bar.can. When the union is θ = 30° from the rest positionis being released. In this case, relative to point B of the fittingthe highest height it can reach and the highestcalculate the speed
A force of P = 20 N is applied to the cable, which causes the 245-kg reel to turn without slipping on the two rollers A and B of the dispenser. Neglect the mass of the cable. Each roller can be considered as an 18-kg cylinder, having a radius of 0.1 m. The radius of gyration of the reel about its center axis is kg = 0.42 m. (Figure 1) Figure P 30% 250 mm OG 500 mm A o OB -400 mm- Part A Determine the angular velocity of the reel, measured counterclockwise, after it has made two revolutions starting from rest. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. W= Submit VE ΑΣΦ 41 Provide Feedback Request Answer vec ? rad/s Next >
Two blocks A and B have a weight of 50 N and 30 N, respectively. They are resting on the incline for which the coemicients of static fniction are = 0.15 and H = 0.25. The spring has a stifness of k 35 N/m (Egure 1) Part A Determine the incline angle 8 tor which both blocks begin to side. Express your answer in degrees to three significant figures. AX voc - O a ? Submit Request Answer Part B Find the required stretch or compression in the connecting spring for this to occur. Express your answer to three significant figures and include the appropriate units. HẢ D) ? Value mm Figure O 1 ef 1> Submit Resuest Answer Provida Feadback