If the 1. The double pulley shown is attached to a 8-mm-radius shaft that fits loosely in a fixed bearing. Ms = 0.45 and M = 0.40 and the weight of the pulley is 25 N, (a) determine the magnitude of the force P required to start raising the load, and (b) determine the magnitude of the force P required to start lowering the load a constant speed. Fr=8mm x 0145 = 3.6 mm = 01366 M х1 фотин 01036m) HP - 20,036 = 0 P 20,036 100 mn 90 mm A 45 mm, 20kg +90361 р. 20,036 MIM 20 kg P CH 23,99 kg Jag

If the 1. The double pulley shown is attached to a 8-mm-radius shaft that fits loosely in a fixed bearing. Ms = 0.45 and M = 0.40 and the weight of the pulley is 25 N, (a) determine the magnitude of the force P required to start raising the load, and (b) determine the magnitude of the force P required to start lowering the load a constant speed. Fr=8mm x 0145 = 3.6 mm = 01366 M х1 фотин 01036m) HP - 20,036 = 0 P 20,036 100 mn 90 mm A 45 mm, 20kg +90361 р. 20,036 MIM 20 kg P CH 23,99 kg Jag

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two bodies is connected in point C, are supported by rigid underlay at an angle α. F is the force acting on right body. We are considering the weight of bodies G and the friction between the bodies and the underlay. Length of bodies l=2000mm.    G1= 160 N, G2= 180 N, α = 30° Find:  1.) Find the magnitude of the force so that it slips on the underlay 2.) Draw the dependence of the force F as a function of the coefficient of friction f (in the range 0-0.5)
A 200 lb block is in contact with a plane inclined at 30ᵒ with the horizontal. A force P parallel to and acting up the plane is applied to the body. If μs = 0.20, Determine: a. The force P required to just impend motion up the plane. b. The force P just to prevent motion down the plane.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire. ( DISCLEIMER: I have allready tried to solve this question before and I have been getting 1307.10N as answer. Seems like this answer is not right.)
A string has a tension T = 5.3 Newtons and connects the two blocks of m1 =3.0 kg and m2 =11.7 kg. Find the value of force F in Newtons assuming the friction is negligible. (only numbers in the box)
A rod 6 ft. long rotates in a horizontal plane about a vertical axis through its center. At each end the rod is fastened to a cord 8 ft. long. Each cord supports a weight of W. a. Set up the equations of motion that are required to solve the problem. b. At what angle will the cord be inclined with the vertical if the speed of rotation is given at 18.42 rpm. 3' 3' 8' 8' w w
For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6
A simple log bridge in a remote area consists of 2 parallel logs with planks across them. The log has an average diameter of 300 mm. A truck moves slowly across the bridge, which spans 2.5 m. Assume that the weight of the truck is equally distributed between the 2 legs. Because the wheel base of the truck is greater than 25 m. Only 1 set of the wheels is on the bridge at a time. Thus, the wheel load on one log is equivalent to a concentrated load acting at any position along the span. In addition, the weight of 1 log and the plank it supports in equivalent to a uniform load of 65 kN/m acting on the log. 1. Determine the max permissible wheel load W based upon the allowable bending stress of of 7MPa. 2. Determine the max permissible wheel load W based upon the allowable shear stress of of 0.75MPa. 3. Determine the max permissible wheel load W based upon the allowable deflection of 6mm. E=7380 MPa
Figure 1 shows a simple system to lift a heavy load. The dimensions a = 3.6 m and b = 1.2 m. The mass of the bar and counterweight is 45000 g, and their weight W acts at the point as shown. The mass of the load being lifted is 20000g (a) (b) If the load is just above the ground, determine the vertical force the person must exert to support the system. If the load is 1 m above the ground, determine the vertical force the person must exert to support the system. 25° Figure 1 20000 g W
A shaft is used to transmit 200 kW at 300 rpm by means of a 200 mm diameter sprocket. Determine the force tangent to the sprocket in kN.
The block of weight W = 10 kN is pulled by the force P inclined at the angle = 15 to the horizontal. Find the smallest force P (in kN, round-off to 2 decimal places) that would cause impending sliding of the block. The angle of static friction between the block and the ground is = 15.
Problem 2 The series of bars shown have their diameters from left to right decreasing by 3 mm, and lengths increasing correspondingly by 0.3 m. If the leftmost member has a diameter and length of 28 mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. Use your calculator. 90 N/mm 45 N/mm 60 N/mm 30 KN -50 KN
If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.