If oil has kinematic viscosity 4 x 10-5 m²/s, andspecific gravity is 0.9, flows from the upper tolower reservoir at a rate of 1870 liter/min in the 23cm smooth pipe (roughness is zero).Given that the minor head losses coefficient ofentrance 0.5, bend 0.32 and outlet 1.9.Use g = 9.81 m/s².O Elevation = }60 mElevation- 130m130 mDetermine the discharge in m³/s, Q.Determine the flow velocity, v.Determine the Reynolds Number, ReDetermine the friction factor.Determine the total head losses (major andminor).What is the elevation of the oil surface in the upperreservoir (point 1)?

Answered: Image /qna-images/answer/597673be-4305-4516-acd4-8ea00e1ba25b.jpg

If oil has kinematic viscosity 4 x 10-5 m2/s, and specific gravity is 0.9, flows from the upper to lower reservoir at a rate of 1870 liter/min in the 23 cm smooth pipe (roughness is zero). Given that the minor head losses coefficient of entrance 0.5, bend 0.32 and outlet 1.9. Use g = 9.81 m/s². O Elevation = ? 60 m Elevation 1= 130 m 130 m Determine the discharge in m³/s, Q. Determine the flow velocity, v. Determine the Reynolds Number, Re Determine the friction factor. Determine the total head losses (major and minor). What is the elevation of the oil surface in the upper reservoir (point 1)?

If oil has kinematic viscosity 4 x 10-5 m2/s, and specific gravity is 0.9, flows from the upper to lower reservoir at a rate of 1870 liter/min in the 23 cm smooth pipe (roughness is zero). Given that the minor head losses coefficient of entrance 0.5, bend 0.32 and outlet 1.9. Use g = 9.81 m/s². O Elevation = ? 60 m Elevation 1= 130 m 130 m Determine the discharge in m³/s, Q. Determine the flow velocity, v. Determine the Reynolds Number, Re Determine the friction factor. Determine the total head losses (major and minor). What is the elevation of the oil surface in the upper reservoir (point 1)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three piezometers have been installed in the confined aquifer having a uniform thickness of 4.6 m. and a hydraulic conductivity of 2 x 104 m/s. Be 140m 61m S10m 235m C EL 12292m EL 122.03m E 120.5 Im Aquiclude Aquifer 6m Aquiclude a) Compute the hydraulic gredient. b) Compute the transmissivity in m2/day. c) Compute the flow rate per unit width of the aquifer in liters/day.
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
A new steel pipe (f= 0.02) of 7000m length and 600mm diameter connects two reservoirs as shown. Including all losses, design the water level elevation in reservoir A such that the required flow rate of 0.5m³/s is achieved. Draw the EGL and HGL. %3D ma eyad Tarawneh z= ??? AMSL A z = 650 AMSL В V
QUESTION 2 , (a) In a rare pipe system design, there is such a case whereas the minor losses is greater than major losses. Describe the case and explain the reason why minor losses value is more than major losses value. (b) Water at 35°C flows steadily in a 4 cm,diameter pipe at velocity of 3.5 cm/s. The head loss is 0.5 m. Calculate: i) the length of theuotual pipe, ii) the pressure loss, and iii) the pumping power required to overcome this pressure drop.
Two tanks A and B have 80 m diffenence in water levels, and are connected by a pipe 0.3 m diameter and 8 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 35 1/s flow rate. Determine the leaving tank А? discharge Find the discharge entering tank B? Coefficient (Tank Exit) = 0.5 %3D Coefficient (Tank Entry) = 1 %3D ha %3D A he 80 m Q1
= gives a cross section of a concrete dam. The subsoil is anisotropic and has 0.8 x 10 in./sec and kv 2.0 x 10 in./sec. Find the rate of flow permeabilities kh beneath the dam per foot length of the dam. And the factor of safety against piping if void ratio of soil= 0.68 and Gs= 2.7. 32 ft 3 ft ZAW ky kh 55 ft Concrete dam TAVAS 557 KN WAY Swise. 275-21 TAVAW
In fig. FV = Water --? If the tank width is 5 m (into the paper) 4m 0 5m C 5m B 1941.6 N 1941600 KN 1941.6 KN
Question- Well Hydraulics Civil Engg. A 20cm well penetrated directly into a confined aquifer of permeability 4.4x10 m/s is with a thickness of 12m. Under steady state condition, the radius of influence is 150m and the drawdown is 3m. The discharge is..?
gle.com/u/0/c/MZE4MZY1MDM1NJ15/a/MzQ5Nzg10TcyOTM0/details jpg. Z, = ? Yol = 8.82 kN/m3 Z = 2. = 130 m 60 m- 7 m 130 m If oil flows from the upper to lower reservoir at a velocity 1.58 m/s in the 15 cm diameter smooth pipe, what is the elevation of the oil surface in the upper reservoir? Activat Go to Set
1. For the setup shown, calculate the pressure difference between points 1 and 2. 2 Oil Oil sg = 0.8 sg = 0.8 1m 2.3т »Hg Hg 0.7m 0.4m 0.8m
Problem 9-36 pipe bend shown is in a horizontal plane. A fluid weighing 8.615 kN/m enters the bend with a velocity of 3.5 m/s and a pressure of 280 kPa. Neglecting head loss, find the force required to hold the bend in place. The Ans 10.4 kN 65 200 mm O 80 mm diam