X = 5Y = 4 b) (i)A DC/DC boost converter is operated in continuous conduction mode(CCM). Assume the input voltage (Vin) is (30+X) V, the output voltage(Vout) is 120 V, and the output resistance (R) is 10 , the ESR of theinductor (R₁) is (0.04+0.001*Y) Q. Calculate the duty cycle D andefficiency of the boost converter.Note that XY are the last two digits of your student number. Forexample, if your student number is C1700123, then X=2, Y=3;30+X=32, 0.04+0.001*Y=0.043.(ii) A DC/DC buck-boost converter is operated in discontinuousconduction mode (DCM). Derive the voltage transfer function Vout/Vinin terms of the duty cycle D.(iii) A DC/DC buck-boost converter is operated in DCM. Assume the inputvoltage is 15 V, output voltage is 10 V, inductance is (40+Y) µH,switching frequency is 20 kHz, the output resistance is 15 Q. Calculatethe average current of the diode.Note that Y is the last digit of your student number. For example, ifyour number is C1700123, then Y=3; 40+Y=43.

Step up or boost converter is used to obtain the output voltage greater than the input voltage. To…

(i) A DC/DC boost converter is operated in continuous conduction mode (CCM). Assume the input voltage (Vin) is (30+X) V, the output voltage (Vout) is 120 V, and the output resistance (R) is 102, the ESR of the inductor (R₁) is (0.04+0.001*Y) N. Calculate the duty cycle D and efficiency of the boost converter. Note that XY are the last two digits of your student number. For example, if your student number is C1700123, then X=2, Y=3; 30+X=32, 0.04+0.001*Y=0.043.

(i) A DC/DC boost converter is operated in continuous conduction mode (CCM). Assume the input voltage (Vin) is (30+X) V, the output voltage (Vout) is 120 V, and the output resistance (R) is 102, the ESR of the inductor (R₁) is (0.04+0.001Y) N. Calculate the duty cycle D and efficiency of the boost converter. Note that XY are the last two digits of your student number. For example, if your student number is C1700123, then X=2, Y=3; 30+X=32, 0.04+0.001Y=0.043.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The inductor current of a buck-boost converter is shown in the figure. The minimum inductor current is zero and the peak value is 5A. The load resistor 5 A value is equal to R=702 Assume that the output voltage ripple is 1%. All components are ideal. Determine. a) Duty ratio. b) Output voltage. c) Input voltage d) Inductor value e) Capacitor value. 12μ 20μ 32μ 40μ t,sec
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.
An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the chopper frequency is 200 Hz. The maximum peak to peak ripple current is equal to: Select one: a. 30A b. 55A c. 90A d. 75A
a) Draw the basic topology of a buck converter. b) Design a buck converter to produce an output voltage of 18 V across a 10 2 load resistor. The output voltage ripple must not exceed 0.5 percent. The de supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
The main function of a boost converter is to: A. Step up or down the input voltage B. Step up the input voltage C. Step down the voltage D. Keep the converter in continuous conduction mode
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz
Part 2: In a step-up converter, consider all the components to be ideal, Let Va be 8-16 V, V. 24 V (regulated), fs-20 kHZ, Po ≥ 6 W. i). Calculate the minimum inductance L required to keep the converter operation in continuous-conduction mode under all conditions. ii). Specify the value of inductor for a maximum ripple of 3%. iii). Design a capacitor for part (i) and (ii) with a voltage ripple of less than 2%.
ZEV * OMANTEL I. A moodle1.du.edu.om Question 2 Not yet answered Marked out of 2.00 P Flag question A buck converter produces an output voltage of 100 V across a 100 Ohm load resistor. The output voltage ripple is 0.5 %. The output current ripple is 2 A. The dc supply is 200 V. The switching frequency is 1 kHz. The value of the inductor is: Select one: O a. 25.00 milli Henry b. 35.25 micro Henry O c. None of the above d. 88.55 micro Henry O e. 75.15 nano Henry Previous page Next page
Find the delay angle of 1 phase half wave converter has 120V supply rms voltage with the value of the resistor is 10Ohm. The average output voltage is 25% of the maximum possible output voltage then find the delay angle.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?