HWAA traingular beam Beomm wide by 30omm height is Pinned at A,suPPorted by a cable CD and Carries a load (P) as shown in figure, Determinethe max Valne of (P) that will not exceed a ombined normal stress of120 Mla?Ans/ Prat - loo.3 WHoW:B Find the max Valne of (P) that canbe aPPlied on the Cantilever beamShown in figure , knowing that the max Combined stresses will not exceed(22.67MPa)in tension and (17.33 MPa) in cemPression?Ans/ Pmax3D25W450mmtoCable30omm150mm50mm300mm2mFig. (A)fig. (B)

Answered: Image /qna-images/answer/ac27ec18-4826-4d47-9287-c2679c7d4421.jpg

HWAA traingular beam Beomm wide by 30omm height is Pinned at A, SuPPorted by a able CD ad Carries a load (P) as shown in figure, Determine the max Valne of (P) that will not exceed a ombined normal stress of 120 Mfa? Ans/ Pa = loo.3 W HoW:B Find the max Valne of (P) that canbe apPlied on the Cantilever beam Shown in figure ,knowing that the max Combined stresses will not exceed(22.67 MPa)in tension and (17.33 MPa) in comPression? Ans/ Pmnx 3D25W 450mm to Cable 300mm 150mm 300mm 50mm 2m Fig. (A) fig. (B)

HWAA traingular beam Beomm wide by 30omm height is Pinned at A, SuPPorted by a able CD ad Carries a load (P) as shown in figure, Determine the max Valne of (P) that will not exceed a ombined normal stress of 120 Mfa? Ans/ Pa = loo.3 W HoW:B Find the max Valne of (P) that canbe apPlied on the Cantilever beam Shown in figure ,knowing that the max Combined stresses will not exceed(22.67 MPa)in tension and (17.33 MPa) in comPression? Ans/ Pmnx 3D25W 450mm to Cable 300mm 150mm 300mm 50mm 2m Fig. (A) fig. (B)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

HWAA traingular beam Beomm wide by 3eomm height is Pinned at A, SuPPorted by a cable CD and Carries a load (P) as shown in figure, netermine the max Valne of (P) that will not exceed a 120 Ma? Ans/ Pmax combined normal Stress of = loo,3 a HiW:B Find the mux Valne of ) that can be aPPlied on the Cantilever beam Shown in figure , knowing that the max Combined stresses will nat exceed(22.67 MA)in tension and (17.33 MPa) in com Pression? Ans/ Pmnt =25 W 450mm to 4 Cable 30omm 150mm N.A ISom S0mm 300mm 4m 2m Fig. (A) fig. (B)
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx= 25 W 450mm 150mm N.A 1 2 S0mm fig. (B)
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Assiynment 11 20KN 3KN/m 4.5 m 1.5m 3 m SO mm Section of T-beam: 130 mm (50 mm The T-beam is subjected to the Toad hing shown. Cal culate the manimun skear stress in the beam, and draw shear stress distrib utyon over the cros secton at this critial location, where manimum shear stren occurs.
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
265KN 1.75ml Cross Section K2,5m A75m 1ス5m thee Determine the Bending Stress at Sectlon D-D
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
Problem 1.10 A har of steel. having a rectangular crass-secton 7.5 cm by 25 cm, carres an axiai tensile load of I8KN stimate the decrease in the length of the sudes ef the cross section if Young's motulus, E, is 20 GNm and Poissn's tatr, v.