Here x = 3 model and parameter when operating in region A? e model and parameter when operating in region B? ne device model and parameter when operating in region C? he 4. If the device is operating in region D, it can be modeled as a Voltage Source in series with a Resistor. What is the value of the voltage source and resistance? (Write the value of voltage with the proper sign.) 5. If the device is operating in region E, it can also be modeled as a Current Source in parallel with a Resistor. What is the value of the current source and resistance? (Write the value of current with the proper sign.) 6. If the voltage across the device is 3V, what is the operating region? What is the current through it?

Here x = 3 model and parameter when operating in region A? e model and parameter when operating in region B? ne device model and parameter when operating in region C? he 4. If the device is operating in region D, it can be modeled as a Voltage Source in series with a Resistor. What is the value of the voltage source and resistance? (Write the value of voltage with the proper sign.) 5. If the device is operating in region E, it can also be modeled as a Current Source in parallel with a Resistor. What is the value of the current source and resistance? (Write the value of current with the proper sign.) 6. If the voltage across the device is 3V, what is the operating region? What is the current through it?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

The volt–ampere characteristic of a certain two-terminal device is a straight line that passes through the points (2 V, 5 mA) and (3 V, 15 mA). The current reference points into the positive reference for the voltage. Determine the equivalent circuit for this device.
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
The zener diode shown in the circuit below is being used for voltage regulation. Determine the percentage line regulation. Assume that R = 742.5 N, V,,= 10.9 V @ I,,= 35 mA, I, = 0.5 mA, I= 53 mA, and R,= 12 2. ZT 'ZK 'ZM Voltmeter to measure Vz Vs Component_1
If we have a voltmeter, during the measurement do we need a voltmeter with high or low input impedance to measure current. How about when we need to measure voltage drop. Please explain. ..
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance? If a full-wave rectifier is needed?
(a) State one possible reason why the diodes have different knee voltage values. 2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has UTM higher dynamic resistance than diode B. 5 UTM U UTM Ip UTM TM 3 UTM UTM O UTM UTM UTM UTM & UTM 03 TM UTM 0.68 VD Figure A.1 State one possible reason why the diodes have different knee voltage values. 5 UTM & UTM M 3 UTM (b) Based on Figure A.1, identify the knee voltage of UTM (c) Draw with complete labelling an equivalent circuit that represents the circuit in UFigure A.2. Consider practical diode model. TM 5 UTM 5 UPde BE UTM & UTM & UTM 1 ΚΩ Diode B 5 UTM O UTM UTM & UTM & UTM 1.5 V 5 UTM UT 5 UTM 3 V 5 UTM O UTM Figure A.2 M G UTM 5 UTM 5 UTM & UTM 5 UTM UTM
Consider the circuit given in Figure (Q4). Let V, = 0.8 V and R = 100 0, find: a) The value of C that results in a ripple voltage not larger than 1 V peak-to- peak. b) The DC voltage at the output c) The current through the load d) The diodes' conduction angle D, 12V (ths) 6. HZ R + Figure (Q4)
Q.7 Light-emitting diode (LED) is simply a diode that is designed to emit light. Voltage drop for LED is 0.8V. What happens to the LED when it is connected to the voltage source as in Figure A1? Why? (Describe in terms of majority carrier movement). LED 5V 1kQ Figure Al
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
Q 2) A single phase half-wave uncontrolled rectifier with RL load is shown With R=1002, La 0. 1H w-377rad/s and V 100V, Determine: a) An expression for the load current i(t). b) The value of the current at t3D16 ms. c) The average load current (1C WLialx197=ア7.9 =121 V, = V, sinfar) 17.2 0.360
Rg + Iz Is Vs Vz RL V Design the circuit above such that Vs = 12 V and RL = 1 kQ. You can choose any appropriate Zener Diode from the given specification sheet. What if the supply voltage varies by ±15%, what is the variation in output i.) voltage (if present)? ii.) Explain what would happen if the load is increased to infinity. (You can use calculations as support)
below diagramshows a silicon transistor with B = 100 biased by base resistor method. Draw the d.cloadline and determine the operating point. %3D