Hello good Afternoon Sir, Permission, i have a question in my homework. The following bellow is question. Please advice. Thank you Regards, Irfan (Look at the picture above. What's a hw/hm?)

Q: (e) Write about the difference in working principle between induced-draft counterflow and…

A: INDUCED DRAFT COUNTERFLOW COOLING TOWER NATURAL DRAFT COOLING TOWER 1. Cooling is achieved by…

Q: ycle thermal ef

A: Givnen as,T=390°CP=9MPa

Q: 21 What are the methods of heat tran Ler during Preg nancg ?

A: The major heat transfer mechanism occurs during pregnancy or at time of newborn into environment as…

Q: ?What is the sp

A: Given data:

Q: A tepki kuvvetinin büyüklüğü ne olur ?

A:

Q: What is the first fuel used before the adoptation of crude oil?

A: What is the first fuel used before the adaptation of crude oil?

Q: speed, Wh

A:

Q: S teath oulat

A:

Q: s Tafel p

A: introduction: here we have to explain tafel pot.

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: what is the byproduct for alcohol distillery

A: the final molasses is a by product in the sugar mill Contain, residual sugar, glucose and fructose.…

Q: the amoun

A:

Q: What is the operation of CNT storage?

A: CNT storage: Here CNT storage means carbon nanotubes storage. Basically it is a tube made of carbon…

Q: a M at at ww.

A: The resultant force by the fluid on the object is known as hydrostatic force. The location of the…

Q: Energy-saving opportunities are present everywhere in compressed air systems, it just takes minimal…

A:

Q: 1. Draw the FBD of member ADB 20 Il

A:

Q: What are the differences between HAWT and VAWT?

A: HAWT- Horizontal Axis Wind Turbine VAWT- Vertical Axis Wind Turbine

Q: the bernoulli

A: Given; Determine the condition of Bernoulli Eq,Within boundary layer for a steady incompressible…

Q: 9

A: Dehydrator & Desalter

Q: What are fan curves?

A: Fan curve: The fan curves are graphs drawn between pressure and air volume handles by fan. The air…

Q: wwwww

A: Given-Information:- Mass of Tear-Drop,m = 2.00 kg Length, l = 0.28 m  T = 11 sg = 9.81 m/s2…

Q: A- What is meant by the term superheat?.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Discuss the basic operating principle of Internal combustion engines (ICE) we are currently using…

A: The ICE or internal combustion engines are the engines in which the combustion of fuel take place in…

Q: State any 15 Advantages of FBC Boiler also give one line explanation of every advantage you state.

A: Introduction: In India, the majority of the coal that is accessible is of poor quality, has a high…

Q: 6. 7

A: Name of equipment used in the Wet Crude oil Treatment plant at Ain Zaleh fields. 6 - Pressure vessel…

Q: Q-1: Fill the blanks with suitable words or phrases: 1- The basic structure of a matter that carries…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Why trap is used after CFWH

A: Explanation  The trap are used after CFWH to allow to pass only liquid not vapour.It also reduce the…

Q: What is the most important reason why reusable launch vehicles have typically been more expensive…

A: In general, flight operations are expected to be more expensive for reusable vehicles due to added…

Q: Could you please help me with my hw? Thank youu

A: Given that:  x = 3 sin 3t + 4 cos 3t   To prove :    a = - ω2x

Q: Consider a 4 stroke SI engine with a bore of 0.1 m. The spark is ignited 20 degrees bTDC. It takes 6…

A:

Q: COP for the HP?

A: Given; An industrial heat pump operates between the temperature of; T1=270 C=27+273T1=300 KT2=-130C…

Q: Q2. An automobile has 3.2 liter, four-cylinder, and four-stroke cycle engine operating at 2400 rpm.…

A:

Q: How effective the waste water can be removed from crude oil and explain the process?

A: Given Crude oil To find Process of wastewater treatment

Q: 4. Is a fire hydrant more likely to be cast or forged? Why?

A: Is a fire hydrant more likely to be casted or forged? The fire Hydrant are more likely to be Casted,…

Q: Q1. An SI engine operating at 1200 rpm has a 10.2 cm bore with the spark plug offset by 6 mm from…

A:

Q: gh illustrations explain the process of TIG W

A: introduction: we  have to explain about TIG welding.

Q: Sketch possible path of the welding fume to the inlet of fume extraction duct and estimate the…

A: Given: To find: Sketch path of welding fume

Q: non whe

A: Angular acceleration,  α = 27 θ Since,α = dωdt              = dωdt dθdt               = ωdωdθ where…

Q: A merciry makes an emole of 130 with respect to the \rertical when in contact with Clean gleed. How…

A:

Q: An engineer was tasked with evaluating a heat and power generation unit for an aluminium smelting…

A: Given data: Power requirement per smelting processing line = 0.6 MW Overall thermal efficiency = 35…

Q: Draw the fréé bódy diagrams for each part in the figures below:

A:

Q: 3Airflows omareservoir where P=300 k Pd& To- beok threugh a threat t. Section@ whern there is a s…

A:

Q: List at least 8 Innovative methods to collect dry residual biomass in Muscat.

A: The innovative methods to collect dry residual biomass in Muscat are: There are some scientific…

Q: can you calculate also the diameter of stack

A: Given      Density of gas = 0.7756 kg/m3                 Draft, h = 56.954 m     Mass of fuel, m =…

Q: Followin g 1-6lowing oxy Jen Jas by lance in BoFto Steal Making -add limestole in blast f urnace.…

A:

Q: What's the Cv for air at 30 to 60℃?

A: The value of  Cv for air at 30 to 60℃ Cv= 0.718 KJ/kg-K as value of Cp = 1.007 KJ/kg-k