he term 'Centroid' is (A) The same as centre of gravity (B) The point of suspension (C) The point of application of the resultant of all the forces tending to cause a body to rotate about a certain axis (D) None of the above

he term 'Centroid' is (A) The same as centre of gravity (B) The point of suspension (C) The point of application of the resultant of all the forces tending to cause a body to rotate about a certain axis (D) None of the above

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.15P: Two 12-kg spheres are placed 400 mm apart. Express the gravitational attraction acting between the...

See similar textbooks

Related questions

Q: From a solid homogeneous hemisphere of radius r, it is desired to cut out a cone the base of which…

A: Here the following figure from the given question

Q: Use Image below Question: Gate AB is 2 m long and 1.8 m into the paper. Neglecting atmospheric…

Q: The uniform lamina of density 8 kg/m²". for a=8 mb=1.5 m.ca1.7 mde1.9 m, x-co-ordinace of shape (1)…

A: Given data: a=8 m b=1.5 m c=1.7 m d=1.9 m

Q: Determine the absolute weight and the weight relative to the rotating earth of a 98-kg man if he is…

A: Given as per question weight of the man =98 kg The angle of latitude =360

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's centroid from axis y0.

Q: If a walking stick with a mass of 300 g can be balanced by placing a mass M of 120 g at a distance…

A: Given data as per question Mass of the walking stick =300 g Placing mas =120 g Distance of the mass…

Q: An automobile with a mass of 1360 kg has 3.05 m between the front and rear axles. Its center of…

A: Consider the diagram shown below for the automobile as shown below. Here R and F are the reactions…

Q: At what altitude h above the north pole is the weight of an object reduced to 75% of its…

A: Given question: At what altitude h above the north pole is the weight of an object reduced to 75% of…

Q: nonuniform bar 2 m long is horizontal and is in a state of equilibrium when supported at the center.…

Q: If the plunger cylinder is with of area 12.5 m2 which lifts the other end of ram cylinder which is…

Q: This type of support carries force perpendicular to the surface of the support wherein it allows…

A: Explanation: In the fixed support there is no movement and having three support reaction namely…

Q: Q3: A: A half circle of area made from wood, while the other half made from metal. Can you consider…

A: Centroid :- It is the location where entire Volume or Area (for 2D) of the object is concentrate.…

Q: A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN %3D…

A: Find magnitude of reactive force at point O.

Q: The Centre of the pressure of a plane surface immersed in a liquid equal to the weight of the liquid…

A: The centre of the pressure of a plane surface immersed in a liquid is equal to the weight of…

Q: BOX 1 (B1) BOX 2 (B2) Density B1 = 8.8 g/cm^3 Density B2 = 9.3 g/cm^3 %3D 100x100x100 cm 100x100x100…

Q: center of gravity

Q: The indicated location of the center of gravity of the ( 16 kN ) pickup truck is for the unloaded…

A: Given that, Load at the center of gravity, W=16 kN,Reaction at A and B =NA=NB=N Drawing the free…

Q: Centroid of an area always lies on the axes of symmetry. Justify this statement.

A: Solution:

Q: Given that the weight of the leg (COG located 8 inches from the axis) is 4 kg, a 25 lb weight is…

A: Weight of the leg, Wleg= 4 kg= 4(9.81)= 39.24 N Distance between the point where weight of the leg…

Q: Determine the absolute weight and the weight rela- tive to the rotating earth of a 60-kg woman if…

Q: . An architect wants to build a wall with the profile shown. To estimate the effects of wind loads,…

A: Given question belongs to subject Solid Mechanics and can be solved using the concepts of Centroid…

Q: lid cylinder of relative density 0.8 is floating on water with its axis vertical. Its diameter and…

A: as per the principle of flotation weight of body = weight of water displaced. if x is the height of…

Q: Based on the newton's second low of motion, the mass is the force applied on a system Ture O False O

A: Given Statement:- Based on the newton's second low of motion, the mass is the force applied on a…

Q: Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg.

Q: A body weighs 250 lb at the earth's surface. Determineb. The weight of the body 500 mi above the…

A: Given data Weight of the body at earth's surface, Fe = 250 lb. Take the radius of the earth as, Re…

Q: Question # 2 A 15-m-long rod thickens from left to right so that its density is 8(x) = 1+ Kg/m.…

A: Given: Length of the rod is 15 m. Linear mass density is δx=1+x15.

Q: At what altitude h above the north pole is the weight of an object reduced to 53% of its…

A: Given data W'=0.53 W Here, W' is the weight at height and W is the weight on the surface of the…

Q: .A railway engine weighing 60 tonnes is moving with a speea of 10 m/sec on a circular track whose…

Q: A hemisphere of 60 mm diameter is placed on the top of the cylinder having 60 mm diameter. Find the…

A: Given: Diameter of the cylinder and hemisphere is 60 mm. Height of the cylinder is 100 mm.

Q: For the orange shaded area shown in the image below, if the coefficients for the function a = 2.2…

Q: The front wheels of a truck support 2000lb, and its rear wheels support 3500lb. The axles are 12ft…

Q: If the mass of cylinder C is 40 kg. determine the mass of cylinder A in order to hold the assembly…

Q: When an object has multiple lines of symmetry, its centroid is located at the intersection of the…

A: In the above statement it is given that the object having more than one line of symmetry has…

Q: Find the centroid (ã, ỹ) of the shaded area, given the function: y = 2-x* and L = 3 ft.

A: Given data: - The equation of curve is y = 2x4. The length L is L = 3 ft.

Q: can you show with numerical proof that centroid will stay same

A: Given data as per the question Height of web =60 mm Width of flange = 60 mm Assuming the thickness…

Q: Calculate the mass m of a body that weighs 600 lb at the surface of the earth .

A: Weight of the body W=600 lb

Q: Write a brief report on the subject of engineering mechanics that was studied in the first course of…

A: since you have posted a multipart question so as we solve the first three part of the questions if…

Q: A half circle of area made from wood, while the other half made from metal. Can you consider the…

A: Centroid is the geometric center of the figure at which whole area is assumed to be concentrated.…

Q: a m2 m2 b b m, a 10 mm The above-shown cross-section is symmetric about Y-axis. For a = 8 mm, b = 4…

A: Given: Length of rectangle→L=10 mm=0.01 m Because→a=8 mm=0.008 m and→b=4 mm=0.004 m And the given…

Q: A body weighs 250 lb at the earth's surface. Determine c. The weight of the body on the moon's…

A: Given weight of the body on the earth's surface = 250 lb…

Q: Given that the weight of the leg (COG located 8 inches from the axis) is 4 kg, a 25 lb weight is…

Q: Centroid of an area always lies on the axes of symmetry. Justify this statement

A: The point corresponding to the geometric center of an object is known as the centroid.…

Q: The center of gravity of the eccentric wheel is at point G. Determine the maximum angle θ of the…

A: Consider the mass of the wheel as m and the roughness of the surface be μ. Draw the free-body…

Q: The plastic block shown below measures I.5 m xl.S m x(.7 m and has a specific gravity of 0.38. The…

Q: Calculate the mass of a body that weight 600lb of the surface of the earth

A: Given Data The weight of the body is: W=600 lb When the weight of any object or the body is…

Q: 1) the resultant hydrostatic force, the line of action is on a centroid of surface area b center…

A: 1) The resultant hydrostatic force, the line of action is on: a centroid of surface area…

Q: Plunger (weightless) Area is 0.003 m² piston mass 1000 kg , area of piston is 0.3 m² density of oil…

A: Area of Plunger, A2=0.003 m2Mass of piston, M1=1000 kgArea of piston, A1=0.3 m2Density of oil,…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The term 'Centroid' is

(A) The same as centre of gravity

(B) The point of suspension

(D) None of the above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The method of locating the center of gravity of a mass or an area is based on the method of determining the resultants of parallel force systems. -True -False
A uniform sheet of metal 6ft square weighs 60lb. If the following weights are hung on each corner of the square in a consecutive manner: 20Ib at A, 60lb at B, 80lb at C, & 40lb at D, find the center of gravity of the system.
Figure(a) depicts a head-on view of a 1000 kg mass private airplane flying in a state of equilibrium. The force labeled P represents the lift force acting on each wing, and W represents the gravitational weight of the craft. Fig. (b) depicts a more detailed view of the wing ABCD showing its physical dimensions and the assumed location of the lift force P. The wing has a mass of 200 kg and a center of gravity at point B. The wing is attached to the fuselage at point A, which can be modeled as a pin connection. The wing is supported by a pin-connected strut BE whose mass may be neglected. (a) Sketch a free-body diagram of the forces acting on the wing depicted in Fig (b). Compute the vertical lift force P. (c) Compute the forces supported by the strut BE and the pin at A. Hint: You may model the wing as a two-dimensional structure where all forces lie in the same plane. (a) P XERO y W (b) 1.4 m + 2 m B с 0.6m 2.4m D
gravity of the body at a distance (a) from the bottom of the hemisphere. 3. A body consisting of a cone and hemisphere of radius (r) on the same base rests on a table, the hemisphere being in contact with the table. Find the greatest height of the cone, so that the combined solid may be in stable equilibrium. [Ans. 1.732 r] Find the centre of gravity a con man
2. A solid consists of a cylinder and a hemisphere of equal radius fixed base to base. Find the ratio of the radius to the height of the cylinder, so that the solid has its centre of gravity at the common face. (Ans. 2:11 Hint. For stable equilibrium, the centre of the body should beelow the common face or maximum lie on it. So take the centre of gravity of the body at a distance (a) from the bottom of the hemisphere.
Q2 : Locate the center of Mass ( X , Y , Z ) of the Homogeneous Block Assembly Shown in Fig ( 2 ) ?
on a table, the hemisphere being in contact with the table. Find the greatest height of the cone, so that [Ans. 1.732 r] 4. Find the centre of gravity of a segment of height 77 mm of a sphere of radius 150 mm. the combined solid may be in stable equilibrium. [Ans. 100 mml
You must exert a force of 52 lb to support a load in a wheelbarrow such that the handles are parallel to the ground. Your hands are gripping the handles 3.1 ft from the axle. The load in the wheelbarrow is 144 lb. How far is the center-of-gravity of the load from the axle?
Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg. Mr M: 3. 2.
45 N Ans. (a) 34 N, 0=280 (b) dRA = 11.64 mm from B to the left; dRc3D62 mm below B 36 Dr. M.S. Meddah 3.116 A 160-N motor is mounted on the floor. Find the resultant of the weight and the forces exerted on the belt, and determine where the line of action of the resultant intersects the floor. 700 N 30° 50 mm -300 N 50 mm Final result: Resultant, R = 925.92 N and 0 = 11.840 x= -582.22 mm i.e. resultant intersects the floor 582.22 mm to the left of the vertical centerline through O. 37
If a rigid body experiences motion, the forces acting on sum of the moments of the body about any point P is equal to Ipx A. general plane, internal rotational, external В. c. general plane, external internal, general plane D.
A truck has a mass of 4820 kg and a wheelbase (distance between front and rear wheels) of 4.8 m. Ifthe center of mass of the truck is located 1.9 m behind the front wheels, where should a 5450 kg load beplaced (relative to the front wheels) in order to have equal weight on both sets of wheels?