he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.

he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Related questions

Q: PROBLEM 1. The shafts are made of A-36 steel and both have 100 mm diameter. If a torque of 60 kN.m…

Q: The solid-circular shafts are connected by gears at B and C as shown below, and having the same…

A: Given Data Shear modulus of shafts is:G=75 GPa Diameter of shafts is :Do=24 mm Length of shaft 1 is…

Q: In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a…

Q: The shafts are made of A-36 steel and each has a diameter of 80 mm. Determine the angle of twist of…

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The allowable shear stress = 100 MPa The frequency of shaft A, NA = y = 20 Hz The diameter of…

Q: Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The…

Q: The rotating solid steel shaft (Fig.1 a) is simply supported by bearings at points B and C and is…

Q: h

A: Given

Q: C 8 10 Determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a…

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A: Given:Torque acting at A, TA=105 N.mTorque acting at B, TB=314 N.mTorque acting at C, TC=372…

Q: The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW…

Q: The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM. The shaft is…

A: Given, Total power being transmitted = P = 65 hp = 4.29 x 105 lbf-in/s Rotational speed of shaft = N…

Q: A solid circular steel shaft having an outside diameter of 1.75 in. is subjected to a pure torque of…

A: Given data: ◆ The diameter of solid circular shaft: D = 1.75 inch ◆ The torque applied on the shaft:…

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…

Q: A propeller shaft C having a diameter of 75 mm is mounted on two bearings B1 and B2 and is driven by…

A: Helical gear In helical gear the teeth of helical gears are cut in the form of a helix on the pitch…

Q: Determine the diameter of a solid shaft which will transmit 440 kW at 280 rpm. The angle of twist…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria Induced torsional…

Q: Need complete solution. The given planetary gear system is composed of 3 Planetary Gears C, Ring…

A: Given: The diameter of carrier shaft, dA = 60 mm = 0.06 m The diameter of planetary gear, dC = 75 mm…

Q: The A-36 steel shaft with a diameter of 30mm is supported on smooth bearings that allow it to rotate…

A: Given: The diameter of the shaft, d = 30 mm = 0.03 m The modulus of elasticity of the A36 shaft, G =…

Q: Determine the maximum torque that can be applied to a hollow circular steel shaft of 100-mm outside…

A: Data given- Outer diameter do = 100 mm Inner diameter di = 80 mm Shear stress = 60 MPa Twist =…

Q: A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D…

Q: A coder F, used to record in digital form the rotation of shaft is connected to the shaft by means…

A: givenFour gears and three solid shaft of dia dradius of Gear C and E =rradius of gear B and D= nr

Q: 3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW,…

A: Answer: The required minimum diameter of the shaft is 24.5 mm.

Q: The solid 25 mm diameter shaft is used to transmit torques applied to the gears. Use G= 80 GPa.…

A: Given: The diameter of shaft, d = 25 mm = 0.025 m The modulus of elasticity, G = 80 GPa

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

Q: A solid shaft 2 m. long is stressed 60 MPa when transmitted a power of 50 kW at 2 rev /…

A: Given: The length of solid shaft, L = 2 m The shear stress in shaft, τ = 60 MPa The transmitted…

Q: 2. The solid 50-mm-diameter shaft is used to transmit the torques applied to the gears. Determine…

A: Given Data D=50 mm

Q: Q3/ The A-36 steel axle is made from tubes AB and CD and a solid section BC. It is supported on…

A: As per given question determine the angle of twist of gear A relative to gear D.

Q: A tapered, wrought iron shaft of length 5 ft, has 2 inch diameter at the fixed end and 0.8 inch…

A: Given data,length=5ftdiameter=2indiameter at free end=0.8intorque T=2000 lb-ing=107psiTo determine :…

Q: The two shafts are made of steel (G=11x106 Ib/in²). Each has a diameter of 1 in., and they are 10…

A: Given: The diameter is d=1.0 in. The shear modulus is G=11×106 lbin2. Torque applied at H of TH=80…

Q: The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the…

A: Write the given data with suitable variables. G=11×103 ksi=11×106 psiPM=3 hpN=1800 rpmζallow=9…

Q: q3..Shaft a transmits 7 hp. Determine the reaction a bearings A and C knowing that these bearings…

Q: A torque of TD- 1235 N-m is applied to gear D of the gear train shown. The bearings shown allow the…

A: GIVEN DATA TWO SHAFT GIVEN CONNECTED WITH GEAR TORQUE IN SHAFT 2 T=1235Nm DIAMETER OF BOTH SHAFT…

Q: The rotating solid steel shaft (Fig.1 a) is simply supported by bearings at points B and C and is…

A: Pitch Diameter of gear D, D = 150 mm Force F act at Ө = 200 Torque at A, TA = 300 Nm At C, D/d =…

Q: The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines…

Q: The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the…

A: Given: The allowable shear stress, τ = 75 MPa The speed of the shaft, N = 300 rpm The power of the…

Q: Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer…

Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…

Q: (Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is driven at 3000 rev/min…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also…

A: Given data, P= 112.5 kW =112500 W N= 200 rpm. θ=1.5° =0.0261799 rad. τ=55 N/mm² =55000000 N/m²…

Q: 3.27 The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on…

Q: The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: A torque of 700 lb-ft is to be carried by a flanged bolt coupling that consists of eight ½-in.…

Q: Determine the gear forces if Gear 1 is rotating at 600 rpm and transmitting 250 kW power. The module…

Q: Determine the angle of twist of end B with respect to end A. Given: The splined ends and gears…

Q: Problem 2: Consider the two gears mounted on the shaft, as shown. Distances are L; = 100 mm, L; =…

Q: A spur gear transmits 35 N · m of torque to the 20-mm-diameter driveshaft. The 5-mm-diameter…

A: Solution: T = 35 N-m D = 20 mm d = 5 mm

Question

The shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.)