Answer would be appreciated The following picture shows part of a beam section which has been structurally idealised. The skins either side of the boom, B, only carry shear stresses. The neutralaxis is shown as the dashed line and note the axes convention.92B91The shear flow just to the right of B is positive and is given by 91.Which of the following statements are correct about the value of q2?Select all that you think are correct, but your mark will reduce if you select any that are incorrect.Oq2 decreases as you go along the web further to the left of the boom, but it remains positiveOq2 remains constant as you go along the web further to the left of the boomJust to the left of the boom, q2 is smaller than 91Just to the left of the boom, q2 is larger than q₁q2 decreases as you go along the web further to the left of the boom, and goes negativeYou need more information to say anything about the value of q2 and how it varies92 increases as you go along the web further to the left of the boomJust to the left of the boom, q2 is equal to q1

The term shear flow refers to the distribution of shear stress within a thin-walled structure caused…

he following picture shows part of a beam section which has been structurally idealised. The skins either side of the boom, B, only carry shear stresses. The neut xis is shown as the dashed line and note the axes convention. 92 B 91

he following picture shows part of a beam section which has been structurally idealised. The skins either side of the boom, B, only carry shear stresses. The neut xis is shown as the dashed line and note the axes convention. 92 B 91

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 6m long solid bar of circle section has 140mm diameter for aluminum for length of 4m, while it has…

A: Length of the solid bar= 6m Dia of Aluminium = 140mm Diameter for aluminum = 120mm

Q: a) Shear distance from the face support b) Value for checking the cross sectional limit for shear c)…

A: P = factored Load from intermediate beam Intermediate beam is carrying Dead load of 29 KN/m and…

Q: a) In the given figure, ABCDEF linear survey was made to determine the area of the site. The lengths…

A: We know that area enclosed by a sector is given by A = θ360*πr2 θ = sector angle θ = 60 degree r =…

Q: A cohesive soil yields a maximum dry density of 18kN/m³ during a standard proctor compaction test.…

A: Dry density=18 kN/m3 G=2.65 Void ratio e=?

Q: Prove that the truss is statically determinate and calculate the internal forces in each truss…

Q: a t2 b t₁ t₁

A: The section given is channel section. It is required to find torsional stiffness, maximum angle of…

Q: Compaction test in the laboratory gave maximum dry unit weight of 18.15 kN/m3 at optimum moisture…

A: maximum dry unit weight-γdmax=18.15 kN/m3optimum moisture content OMC=15%specific gravity G=2.7

Q: A rectangular beam has b = 300 mm and an effective depth of 525 mm. 28th day compressive strength of…

A: A rectangular beam of Width (b) = 300 mm Effective depth (d) = 525 mm Compressive strength of…

Q: Explain - Explain why groundwater is more difficult to clean than surface water.

A: Groundwater and surface water are two primary sources of fresh water on our planet. However, they…

Q: For a horizontal curve, the radius of a circular curve is obtained as 300 m with the desig speed as…

A: Given a horizontal curve with, The radius of a circular curve, R = 300 m. The design speed, V = 15…

Q: The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB shown…

Q: 3.2 A circular basin with radius of R received a rainfall storm. The 6 raingauges were located…

Q: A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of…

Q: he platform scale consists of a combination of third and rst class levers so that the load on one…

Q: 1. Calculate the potential evapotranspiration from an area near New Delhi in the month of April by…

A: Latitude =30° N Elevation =200 m (above sea level) Mean monthly temperature =32.5° C Mean relative…

Q: Use the method of sections to solve for the force in members OA, PQ, and OS. Indicate whether the…

A: Use the method of sections to solve for the force in members OA, PQ, and OS

Q: SITUATION 3: The optimum moisture content of a soil is 19.5% and its maximum dry density is 1.75…

Q: (g) Find the stability of a retaining wall for the following data. (i) Height of Earth retained with…

A: Height of stem: 4.4m Thickness of stem: 0.4m Thickness of footing: 0.40 m depth of footing: D =…

Q: mine the reactions at the supports, then draw he moment diagram. The moment of inertia for each…

Q: Use the column interaction diagrams to determine (P.) value for the short column shown in Figure, if…

A: In order to determine the Pn value based on the given data we need to find Kn value from interaction…

Q: 1). Determine the adjusted load for all columns A B 480 KN 0.600 2200 KN 480 KN D 2200 KN G J 500 KN…

A: The size of column is 0.600×0.600. Length of foundation =0.3+4.5+4.8+0.3=9.9 Width of foundation…

Q: It is required to design a rural highway in Baghdad city, the anticipated peak hourly volume for the…

A: PHF=0.85 DDF=0.6 Truck=%HV=10% Design Service flow for 1 lane= lane capacity=1080 pc/hr/lane Hour…

Q: Any shear load can be represented by the combination of the shear load applied through the and a

Q: A) draw the free body diagram to prove its statically determinate and find the reaction forces at…

A: Find: A) draw the free body diagram to prove its statically determinate and find the reaction forces…

Q: The speed density Relationship + Traffic on osection of reeway ane was Vs = 18-2 In 320 D what is…

A: Given: Speed density relationship: Vs=18.2ln(220D) Maximum flow is the product of the maximum…

Q: A cylindrical water tank of 10 m high is to be filled with water. The tangential and longitudinal…

A: →Height of Cylindrical water tankh =10m→tangential Stress σt=150 MPa =150×106 Pa→Longitudinal Stress…

Q: A 1.5 m x 1.5 m footing is carrying a 400 kN load as shown in the figure below. Depth (m) 0.0 1.0…

A: Footing size =1.5 m × 1.5 m Load =400 kN Poisson's ratio of sand =0.3 Poisson's ratio of clay =0.5

Q: SITUATION 1: A road embankment needs 130 000 cum. to be completed. DPWH requires 96% compaction and…

A: Optimum moisture content ( w) = 17% Maximum dry density = 19.20 kN/m³ Compaction needed = 96%

Q: What harmful effects can occur from over pumping aquifers ?

A: An aquifier is a saturated formation of earth material which not only store water but yields it in…

Q: Find the centroid about the x and y axis by using integration

A: To a circle of radius R = 10in a quarter section is cut. The cut section is symmetrical about the…

Q: The following are slab systems without beams and joists: I. Bubble Deck II. Hole Deck III. Flat…

A: Slab systems without beams and joists are structural floor systems that do not have any intermediate…

Q: Problem A bridge girder consists of W 760 x 161 and a channel C 380 x 50.4 and joined by 2 - 22 mm Ø…

A: Maximum bending stress in tension is the maximum stress in the beam due to the bending moment .…

Q: it requires a sketch can you please provide that as well

A: I have draw the diagram in my copy . It's difficult to draw here so I had prefer it on my copy

Q: (a) Show that the critical depth for rectangular channels is expressed by y. = [a Q²/gb²], where Q…

A: Note: In b and c part of the question, Figure is not provided. Please resubmit the question with…

Q: The beam has a width of 300?? and an effective depth of 525??. The beam is simply supported over a…

A: To determine the required stirrup spacing, we need to first calculate the maximum shear force and…

Q: Consider the beam shown in (Figure 1). EI is constant. Assume that EI is in kN m². Use the…

A: EI = Constant and is in KN•m2 Determine the slope and deflection at B.

Q: [In a river basin a station A was in operative during a storm, while stations B, C, D and E,…

A: Rainfall recorded by station B = 74 mm Rainfall recorded by station C = 88 mm Rainfall recorded by…

Q: or this section, the geometry and sub-section shear forces are shown, when an applied shear force of…

A: Shear center location is independent of transverse force direction and magnitude. When a beam has…

Q: For a sieve analysis laboratory report, describe the objective of the lab. Provide a list of…

A: Sieve analysis is a laboratory technique used to determine the particle size distribution of a…

Q: Situation 1: The natural moisture content of a soil mass is 11%, while its void ratio is 0.63.…

A: Given data in question Moisture content 11% Void ratio 0.63 Specific gravity 2.72 To find out…

Q: In what various ways is it possible for a developer to expand their understanding of site design?

A: Although design and programming are frequently regarded as distinct fields, some individuals are…

Q: Question 1: A 3 m B. 4 kN/m 3 m

A: A simply supported beam with an over-hang portion of 3m. On this beam, a UVL is applied from A to B…

Q: A 10 cm dia pipe carries a fluid with kinematic viscosity of 0.25 Stokes at 22°C. If the flow has to…

A: Given data in question DDiameter10 cm Kinematic viscosity 0.25 stokes Reynolds number 2000 To find…

Q: Using the slope deflection method, calculate the member end moments and draw the shear force and…

A: Given:- A beam is given with a point load and a uniform load The magnitude of the point load = 89 kN…

Q: 3.3 The shape of a catchment is in the form of a pentagon ABCDE. There are 4 raingauge stations…

A: Position cordinates: A(0,0), B(50,75), C(100,75), D(150,0), E(75,-50), P(50,25), Q(100,25),…

Q: Preamble 4 Observation is a three-part process. You must see, assess and communicate. This makes it…

A: Observation theory is a process of systematically gathering information using the senses, assessing…

Q: The steel rod fits loosely inside the aluminum sleeve. Both components are attached to a rigid wall…

Q: Is high hardenability desirable in steels? Explain your answer briefly

A: It is a qualitative indicator of the pace at which a specimen's inner hardness decreases with depth…

Q: Find the internal Forces symmetric from the center

A: Let us name the joint to left half the truss as shown below Consider forces at joint A Consider…

Q: A simply supported wooden beam 100 mm wide, 250 mm deep and 3 m long is carrying a uniformly…

A: Determine the maximum shear stress in the beam.

Question

Answer would be appreciated

The following picture shows part of a beam section which has been structurally idealised. The skins either side of the boom, B, only carry shear stresses. The neutral
axis is shown as the dashed line and note the axes convention.
92
B
91
The shear flow just to the right of B is positive and is given by 91.
Which of the following statements are correct about the value of q2?
Select all that you think are correct, but your mark will reduce if you select any that are incorrect.
Oq2 decreases as you go along the web further to the left of the boom, but it remains positive
Oq2 remains constant as you go along the web further to the left of the boom
Just to the left of the boom, q2 is smaller than 91
Just to the left of the boom, q2 is larger than q₁
q2 decreases as you go along the web further to the left of the boom, and goes negative
You need more information to say anything about the value of q2 and how it varies
92 increases as you go along the web further to the left of the boom
Just to the left of the boom, q2 is equal to q1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Reasons

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
For the element shown in figure. Calculate 1) Principle stresses 2) Maximum 3) Stresses Compenents at ot20 shear stres " the sesults. in-plane Show all on sketches of element. Analytical neat Use Method. >0.8R in MPa 015R MPa R= 780 where
The AD beam, which is fixed at left end, is under various loads as shown below. a) Draw internal load diagrams (Nx, Vy, M2) using the method of section. b) Determine the state of stress at points G, H and I for section B. c) For the corresponding points, indicate the results (i.e. stress components) on a differential element. b2 A B G М F2 2l h bi GIVEN DATA: Fo = 10000 N, F1 1200 N, F2 = 1000 N, qo = 50 N/cm, Mo = 50000 Nem, l = 25 cm bi = 10 cm, b2 = 20 cm, h 12 cm, t 1 cm
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.