H.W: Write the ladder logic program needed to implement each of the following (assume inputs A, B, and C are all normally open toggle switches): a. When input A is closed, turn ON and hold ON outputs X and Y until A opens. b. When input A is closed and either input B or C is open, turn ON output Y; otherwise, it should be OFF. c. When input A is closed or open, turn ON output Y. d. When input A is closed, turn ON output X and turn OFF output Y

H.W: Write the ladder logic program needed to implement each of the following (assume inputs A, B, and C are all normally open toggle switches): a. When input A is closed, turn ON and hold ON outputs X and Y until A opens. b. When input A is closed and either input B or C is open, turn ON output Y; otherwise, it should be OFF. c. When input A is closed or open, turn ON output Y. d. When input A is closed, turn ON output X and turn OFF output Y

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the lamp will light when there are at least 2 switches per circuit.
4. Figure 2 shows a logic circuit with output F Figure 2. Logic circuit with gate I (AND), gate II (AND), gate III (NOT), gate IV (AND), gate V (EXOR) and gate VI (OR) a. Find the Boolean expression of output F. b. The simplified Boolean expression of Output F. c. If the input A and C were High and Input B was Low, what is output F:
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? Explain. b. What is the highest voltage that must be interpreted by a receiver as logical 0? Explain. c. What is the lowest voltage that must be interpreted by a receiver as logical 1? Explain.
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? Why? b. What is the highest voltage that must be interpreted by a receiver as logical 0? Why? c. What is the lowest voltage that must be interpreted by a receiver as logical 1? Why?
Implement the function, W using ONE 4-to-1 multiplexer and other logic gates. b) Implement the function, X using ONE 4-to-1 multiplexer and other logic gates. Implement the function, Y using TWO 4-to-1 multiplexer and other logic gates. d) Implement the function, Z using ONE 8-to-1 multiplexer and other logic gates. Table Q1 ВCD Braille A B D W Y 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 A ololO
12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 Inputs (RES L1 T4:2 PB1 (RES) PLO PB2 -RTO - RETENTIVE TIMER ON PB1 Timer Time base Preset T4:1EN) 1.0 2900 CON) Accumulated -RTO- PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset Accumulated 1780 CON) T4:2 PL DN
12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 (RES Inputs L1 T4:2 (RES PB1 PL PB2 -RTO PB1 RETENTIVE TIMER ON T4:1 EN 1.0 2900 CON) Timer Time base Preset Accumulated -RTO PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset 1780 ON) Accumulated T4:2 PL HE DN
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG