H.W: - For a single phase half wave uncontrolled rectifier if the input supply voltage is (v,- 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- i. Draw the rectifier circuit. ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. iv. If the load is (R-10 2), then determine the mean and rms values of the current.

H.W: - For a single phase half wave uncontrolled rectifier if the input supply voltage is (v,- 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- i. Draw the rectifier circuit. ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. iv. If the load is (R-10 2), then determine the mean and rms values of the current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
For the single phase half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 50 Hz. The load resistor is 5ohm. Determine (a) the average load current, (b) the average power absorbed by the load and (c) the power factor of the circuit.
a) Draw the 3-phase half-wave uncontrolled rectifier circuit for resistive load.b) Briefly explain the purpose of use.c) Draw the sinusoidal input voltages and the output voltage on the load.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
For the half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 60 Hz. The load resistor is 5 ohm. Determine (a) the average load current, (b) the average power absorbed by the load.
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.
Determine the value required for each given condition if an AC voltage with an amplitude of 10 V at a frequency of 50 Hz is the source to each condition. AC meter reading for the given Choose. + AC voltage (V). V_rms (V) of a Half Wave rectifier for the given AC Choose.. + voltage as input. Average of the given AC Choose.. voltage (V). The average output voltage (V) of a Bridge rectifier for the given AC voltage as input. Choose... The average output voltage (V) of a centre tapped rectifier Choose... for the given AC voltage as input. Choose... +
PROBLEM SET 1. Derive the formula for the RMS value for the following a) b) 3m 2. Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. 3. Following the analysis applied to the half-wave rectifier with capacitor filter, show how to arrive at the output waveform for a center-tapped full-wave with filter capacitor. See output waveform on page 90. 4. Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 µF; average load voltage 18 V. Determine ripple factor and average load current 5. Design a half-wave rectifier with a capacitor filter that will deliver to the load an average voltage is 15 V at 280 mA. Ripple should not be higher than 5%. 6. Given: The input to a voltage regulator circuit varies from 11.4 to 12.2 V. The load voltage is to be maintained at 9.1V with maximum…
Q6)Consider a half-wave rectifier circuit with a resistive load of 25 N and a 60 Hz ac source of 110 V rms. For this rectifier the average power delivered to the load equal to Оa. 242 W Ob. 525W Oc. 424W Od. 240W