H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is 4 time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k

H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is 4 time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q7) 10 kg of water in a piston cylinder arrangement exists as saturated liquid/vapor at 100 kPa, with a quality of 50%. It is now heated so the volume triples. The mass of the piston is such that a cylinder pressure of 200 kPa will float it. Find the final temperature and the heat transfer in the proces.. HO [829°C, 25961 kJ]
Q5: A vary large furnace contains hot gas and particles at (1700 C) heat is transferred from gases and particles by convection and radiation to interior surface where temperature is (1500 C) the rate of heat transfer by radiation is (1000 w/ m2) while the unit surface conductance for convection on the interior surface is (15 w/ m?.c ) the furnace wail is (0.6 m) thick and its thermal conductivity (2.5 w/m.c) : 1- Draw the thermal circuit. 2- Determine the rate of heat flow through the wall. Determine the outside surface temperature
Question: 2 kg mass of ammonia initially at P1=7 bars and T1=180 centigrade undergo a constant pressure process to a final state where quality is 85% determine the work for the process kilojoule Note: please do it clear and step wisely thanks in advanced........
Edición P3. A piston-cylinder system contains 1 L of water at 105°C and 85% quality. I know adds energy, causing the plunger to travel until it makes contact with a spring of constant K = 100 N/mm, just at this moment, the volume of the water is 50% greater than the initial. The energy transfer continues until the volume is 1.7 L, and the temperature of the water reached 600°C. Make a schematic of the system according to the statement and calculate the water pressure when T = 600°C. Answer: 198.16kPa
Q3: You have an ideal gas in an insulated container. You compress it from a pressure of 40 × 105 Pa to 20 × 105 Pa, while increasing the volume from 10 to 20 m3. What is the work you done by the gas a- 10 J b- 300 J c- 500 J d- 880 J
CAREFULLY SOLVE. A spring-loaded piston/cylinder assembly contains 1 kg of R-410a as saturated vapour at -20 ℃. Initially, the spring is relaxed (P1=P0) and if the piston hits the stops, the volume doubles. Heat is added to the assembly until a final condition of 800 kPa, 80 ℃ is reached. Find: a) the work done by the process. b) the heat transfer during the process.
An ideal gas of mass I kg is enclosed in rigid insulated container of volume 1 m' (C, =1000 J/kgK, C 800 J/kgK). A stirring paddle attached in system rotates 1000 rotation with constant rpm has torque 100 N-m, then the final temperature (in K) of gas is
The figure shows a P-T graph P(Atm) for an ideal gas. What is the 6+.... internal energy change of the gas between states (i) and (f), if it absorbs 1 800 J heat dur- 2. T(K) ing the process? 300 900
In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a pressure of 100 kPa. Then heat is given to the water until its volume is 0.4 m3. At this point, the piston in the cylinder is fixed with a stopper, but the water in the cylinder continues to heat until its temperature reaches 300 oC. According to this, calculate a) the final pressure of the water, b) the amount of heat given to the water, c) the work done by the piston. d) Show these processes in the T-v (Temperature-Specific Volume) diagram
In a reciprocating air compressor, high pressure air in the cylinder pushes the piston against the external load and expand to a lower pressure. In a test the following measurements were noted:Internal energy of air before expansion = 27 kJInternal energy of air after expansion = 8 kJHeat entering the cylinder during the process = 2 kJSHOW THE DIAGRAM USING THE GIVEN PROVIDED
Ql: A piston-cylinder device initially contains 3 kg of air at 5 bar and temperature 27 °C. The air expands at constant pressure to 0.3 m' and then cooled at constant volume to the 1 bar, then compressed to the initial volume at constant pressure. Finally the air compressed to the initial pressure. Find the total amount of heat and work.
ft lb 4. For a certain ideal gas, R = 77.8 lb R Btu and Cp = (0.2 + 0.0002T) It is %3D lb R heated from 40 °F to 140 °F . For 1 lb mass, find: a. change of internal energy ( answer: 21 Btu ) b. change of enthalpy ( answer: 31 Btu )