H. Two capacitors of 200 and 800 nF, respectively are connected in parallel. The combination is then connected in series with another two capacitors of C and 600 nF connected in parallel. If the total capacitance of the set-up is 500 nF, determine the capacitance C.

H. Two capacitors of 200 and 800 nF, respectively are connected in parallel. The combination is then connected in series with another two capacitors of C and 600 nF connected in parallel. If the total capacitance of the set-up is 500 nF, determine the capacitance C.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Related questions

Q: On the plate of a single-phase transformer, it is written 1800 VA, 2000/200 V, 50 Hz. In the open…

A: Note: The question is not given in correct format, hence it is difficult to understand the exact…

Q: A 60 Hz alternator stator is wye connected with each phase winding having 24 turns of wire. The…

A: f=60HzT=24 turnsϕ=0.103 weber

Q: 3. Consider the circuit diagram below. Solve for the mesh currents I1, I2, and 13 and the voltage at…

A: Given: A network, To find: Mesh currents, node voltage va using mesh analysis. We have to use…

Q: In the circuit below, vi(t) = 5e-4000 cos(3000t) V R = 120, C = 83.3µF, L = 1mH. a.) Find s. b.)…

Q: Find: (a) Vp (b) Vp-p (c) Frequency (d) Period (e) Angular Velocity (f) Phase angle (g) Equation of…

A: Given Peak to peak voltage Time to reach zero from negative peak Value of waveform at 0 degrees

Q: A transformer has a 400-kVA output. If the input voltage is 6.6 kV and the transformer effi ciency…

Q: Q.3: A three-disc suspension insulator string is used for a three-phase, 50-Hz system as shown…

Q: The speed of an alternator rotor in rpm that has 4 poles and is producing a voltage at 45.4 Hertz…

Q: 5. Using nodal analysis, find V₁, V₂ and V3 2 6A ↑ V₁ W 92 M 45 8A 352 W V2 бл W ·422 V3 -8 9 v

Q: A0.26 F capacitor is connected across an AC generator that produces a peak voltage of 9.10 V. You…

A: Given:- C=0.25uF Vpeak=9.10 Volt

Q: 1. A solenoid with 2000 turns is 20-cm long. There is a current if 1.5 A going through the solenoid.…

A: Given data, Number of turns N= 2000 turns Length of the solenoid L=20 cm Current I=1.5 A

Q: 3. Determine Vo. 12 V (+) 82 M Vo 252 W +7V

A: Given circuit:-

Q: k G(s) = s(s+3)(s+4) system with a direct chain transfer function given as 1- Represent the poles of…

Q: The resistance and reactance of the main winding of a 50 Hz single phase induction motor are √3 and…

A: Given: A single-phase capacitor starts an induction motor with, Resistance of main winding, Rm=3 Ω…

Q: r P4. If G is a Time invariant system given by y(t) = x²(t) and H is a linear system given by x(t) =…

Q: Using Thevenin Theorem Find Rth, Eth, and current I1

Q: 1. Calculate the total resistance in the figure given below. Use Delta-Wye transformation. 8Ω, 120…

Q: A feedback control syetm is shown in the figure. Sketch the root locus determining: a) Number of…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: For the given circuit where V = 18 V, use source transformation to find the current i. 2 A www 592…

A: Given: Circuit diagram:

Q: In the circuit below, vs(t) = A₁ cos(25.10¹. t). The switch is closed for t < 0, and opens at time t…

A: Given data: Value of the resistance, R1=3 kΩ Value of the resistance, R2=6 kΩ Capacitor,C1=2 nF…

Q: Charge Q-8.0 x10° C is distributed uniformly throughout a spherical insulating shell of radius R =…

A: Given data, Charge Q=8×10-9 C. Radius R=5.7 cm = 5.7×10-2 m. Distance r=19 cm = 19×10-2 m.

Q: What would be the voltage dessipate across R1?

A: Note Rseries= R1+R2+R3+....1Rparallel=1R1+1R2+1R3+1R4+......

Q: Explain how the resonant frequencies, cut-off frequencies, bandwidth, and quality factor of series…

Q: 25 15 V C₁ 0.1 μF C₂ C₂, 0.47 μF 0.22 μF

A: Given data, Given circuit diagram is,

Q: 8 points charges of 1 nC each are located at the corners of a cube in free space that is 1 m on a…

A: Electric charge Charged material experiences a force when it is exposed to an electromagnetic field…

Q: 4.4. An incandescent lamp 1.5 m away produces the illumination of 150 luxes on the workplace. How…

A: The intensity of the light is inversely proportional to the square of the distance from the source.…

Q: Find the Fourier Transform of the following signals: x(n)= {0,1,5,6} a) b) ↑ x(n)=4"u(n-5) c) x(n) =…

A: Given: a) x(n)=0,1,5,6b) x(n)=4-nu(n-5)c) x(n)=12sin2π5n,0≤n≤60 ,Otherwise To do: we have to find…

Q: An acoustic sensor based instrument is to be designed for measuring the air temperature in a steady…

A: Acoustic Wave Technology Since a mechanical or acoustic wave serves as its sensing mechanism,…

Q: A 50 Hz alternator stator is delta connected with each winding having 40 turns of wire. The rotor is…

A: f=50 Hzϕ=0.148 weberT=40 turns

Q: 4. Use source transformation to find Vx. 20v + 952 W 102 (1 55 M + Vx 10A Je 8₁ (1) 3A

Q: 3. For the figure below, determine the mode voltages at nodes 1, 2 and 3. (Nodal Analysis) 1 492 292…

Q: 3. The unit of magnetic flux density in MKS. 4. The unit of magnetic flux in MKS. 5. The unit of…

Q: A resistor and a capacitor of values 4 ohms and 0.3 farad, respectively, are connected in series.…

Q: 20 Ω 10₁ RL • '40 Ω 50 v

A: According to maximum power transfer theorem, to transfer maximu power fron source to load, tge load…

Q: t 1 is at urrent. e 0.92 pf power and to n load. upplies llel we load has phase bc- °V ch are 2. The…

Q: The distance x, measured in metres, of a downhill skier from a fixed point is measured at intervals…

A: It is given that: t 0 0.25 0.5 0.75 1 1.25 1.5 x 0 4.3 10.2 17.2 26.2 33.1 39.1

Q: 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs…

A: The truth table is drawn as: C A3 A2 A1 A0 X3 X2 X1 X0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 0…

Q: Question No.76 The change in resistance of an electrical strain gauge with a gauge factor of 2.0 and…

A: Given: Electrical strain gauge with gauge factor, G.F.=2.0 Resistance, R=50 Ω Strain, ∆LL=0.001

Q: Q1. For an angle modulation, the modulated signal found to be v(t) = cos(wet + (t)), where (t) =…

Q: FOR THE FOLLOWING CIRCUIT, CONSIDERING THAT VA IS THE SINUSOIDAL SOURCE PRESENTED BELOW, VB A SOURCE…

Q: Q (2) Calculate the closed loop gain of the non inverting amplifier shown below if AO = Infinity b)…

Q: A 200-MHz, left-hand circularly polarized plane wave with an electric field modulus of 5 V/m is…

A: Given data, Frequency f=200 MHz Electric field modulus =5V/m εr=4 Region z≥0

Q: 3. Given the circuit below, use NODAL analysis to solve the circuit. 792 ww 692 1202 Node a: 3 A…

Q: Exercise 1: Humidity detector We propose to study the assembly of figure 1 which allows the ignition…

A: The given circuit is as shown below,

Q: 2: Write a lecture for teaching the complex power fed to an (R-L) load fed from an AC power source…

Q: Determine Q if the S-R FF is driven with the following signals. Initial state: HIGH (C is the…

A: Truth Table of SR FF Clock S R Output 0 X X Memory 1 0 0 Memory 1 0 1 0 1 1 0 1 1 1 1…

Q: The maximum allowable voltage drop, from the supply side of the consumers ser conductors, to the…

A: Distribution system In the case of the distribution system, power is supplied from the main…

Q: 4. Consider the circuit diagram below. A) Simplify the circuit and redraw it to the minimum number…

A: Given,

Q: Find VC (assume a stiff bias circuit). CB HE 10 ΚΩ 1.8 ΚΩ 820 Ω Q₁ 40 V Cc te 1500 I CE

Q: 7. The switch in the circuit below has been closed for a long time. At t = 0 it opens: 6Ω + 12 V 3 Ω…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

H.
Two capacitors of 200 and 800 nF, respectively are connected in parallel. The
combination is then connected in series with another two capacitors of C and 600 nF
connected in parallel. If the total capacitance of the set-up is 500 nF, determine the
capacitance C. /

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A capacitor C is connected in series with a 400 resistor across a supply of frequency 60 Hz. A current of 3 A flows and the circuit impedance is 500. Calculate: (a) the value of capacitance, C, (b) the supply voltage, (c) the phase angle between the supply voltage and current, (d) the p.d. across the resistor, and (e) the p.d. across the capacitor. Draw the Phasor diagram.
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
how do i calculate the inverse capacitance and its uncertainty if the capacitance value 1.8748+/- 0.0006. please show steps im using this example to do my other values.
a. Show how you would connect all five capacitors to get a maximum capacitance and find the maximum capacitance in terms of C. b. Show how you would connect all five capacitors to get a minimum capacitance and find the minimum capacitance in terms of C.
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
Three capacitors each of the capacitance C are given. The resultant capacitance 2/3 C Can be obtained by using them ? a)Two in parallel and third in series with this combination b)All in parallel c)All in series d)Two in series and third in parallel across this combination
a) The voltage across a 20uF capacitance is v. = 50 sin( at - 80) volts and Frequency equal to 100 Hz. Determine the current through the capacitor i and sketch its waveform. b) Define phasor