Given the voltage divider circuit shown, with input voltage of 20V, R₁ = 1kQ and R₂ = 3k, and RLoad = 20k, the output voltage across R2 should be 15V, ±0.1V. Can this voltage divider meet the specification as shown? If yes, prove your answer by showing complete solution. If no, compute for the appropriate value of R2. V=20V. Output voltage R₁ = 1KQ >R₂ = 3ΚΩ R₁ = 20ΚΩ

Given the voltage divider circuit shown, with input voltage of 20V, R₁ = 1kQ and R₂ = 3k, and RLoad = 20k, the output voltage across R2 should be 15V, ±0.1V. Can this voltage divider meet the specification as shown? If yes, prove your answer by showing complete solution. If no, compute for the appropriate value of R2. V=20V. Output voltage R₁ = 1KQ >R₂ = 3ΚΩ R₁ = 20ΚΩ

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
the adjoining figure. This lamp can withstand a maximum voltage 3.0 v 0.4 9. Volt-ampere (V-I) charaeteristics of an incandescent lamp 16thd in and a maximum current 0.4 A. An infinite ladder network consisting a large number of these lamps is also shown in the figure given belo How much maximum voltage can be applied between the terminals A and B, so that no lamp gets damaged? (Use V5 = 2.2). Ans:x4.2V Hint: Curentin all bulls except first is
Part A: A multi-range ammeter is required to measure the current in a certain network. A PMMC instrument has connected as an Ayrton shunt with a four resistor across PMMC. The resistance values are R1 = 0.006N, R2 = 0.0650, R3 = 4.00 and R4 =10.00. The PMMC has Rm = 1kQ and FSD = 50µA. %3D %3D a. Draw the circuit for the multi-range Ayrton shunt. b. Calculate the four current ranges of the ammeter. c. What is the main advantage of Ayrton shunt ammeter compared to parallel type. d. Briefly explain how this device can be calibrated. * Note: Show all calculation details. Part B: The measurement of the voltage from a prototype of a 20V DC power supply were captured by 8 times as shown in the following table: Number 1 2 3 4 6 Voltage (V) 18.5 19.8 20.2 19.9 20.0 20.1 19.7 18.9 Determine the following: 1. the arithmetic mean, 2. the standard deviation of the readings, 3. the probable error. 4. If the voltmeter that used to carry the measurements has an error of 0.5%; calculate the total…
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
A resistor of 20 Ohms and a capacitance of unknown value when connected in in parallel across a 100V, 50Hz supply, take a current of 6A. The combination is now connected across a 100v supply of unknown frequency and the current falls to 5.5A. What is the frequency?
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
Using superstition, find the value of i0 if voltage source at the left is 10, angle - 30 degrees V, and current source is 2, angle zero degrees. A total of three sources will be considered, separately. The 24 volt source is DC. When this source is acting alone, the capacitor will be open-circuited.
A resistance of 12 ohms and capacitance of 0.01 farad is connected in series with a 200 volts battery. Find the charge after 0.5 second and the current after 0.4 second
8 The figure is a graph of . Current Voltage the current across a voltage as a function of the potential difference through it the resistance as a function of the current across a component the current through a component as a function of the voltage across it O All three of the above (a), (b), and (c) are true O None of the above (a), (b), or (c) is true
In the circuit above, if V1 = + 28V, R = 17,612, RL = 14,3 and the zener voltage is 8,0, what is the peak point of the voltage falling on the resistor R in the negative alternans of V1?
Here you see a circuit with a battery, fully uncharged capacitor, C and a bulb. What would happen to that electric bulb in the circuit when you switch on the circuit? Moreover, what would be the consequences if you switch off the circuit when capacitor is fully charged? Answer step by step .answer must be correct. Do all calculation follow image.