Given the proposed longitudinal profile of the centerline of a rural two-lane highway as follows: PVLu STN 10+0) PVL: Elev. 100 ft G-2% Ge0% L=? Ly=? a) Calculate the required minimum design lengths (to meet the SSD requirements) of the three back-to-back vertical curves on this section of the roadway to accommodate a continuous design speed of 50 mph.

Given the proposed longitudinal profile of the centerline of a rural two-lane highway as follows: PVLu STN 10+0) PVL: Elev. 100 ft G-2% Ge0% L=? Ly=? a) Calculate the required minimum design lengths (to meet the SSD requirements) of the three back-to-back vertical curves on this section of the roadway to accommodate a continuous design speed of 50 mph.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Regarding superelevation, when a median is less than 3 m wide, the entire pavement and median may be rotated about the median 01 Centerline 02 Outside edge 3 Inside edge 04 All of the above
The arterial road with a 100 km/h design speed will be constructed on the flat terrain. At one section, the equal tangent vertical curve as shown in Table 3 is proposed. Table 3: Parameters of Vertical Alignment Length 490 m PVC station 3+700.000 PVC elevation 460 m Initial grade -3.5% Final grade 6.5% (a) Calculate the stationing and elevation of the low point, PVI and PVT. (b) Calculate the minimum length of curve to meet stopping sight distance requirements
Design a highway with the following criteria (Determine the minimum radius, widening and check if it needs transition spiral) Design speed = 85 kph I = 20o e = 0.06 sight distance = 125m m = 10 m 2 lane road Typical car wheel length 2.5 m Width of pavement per lane = 3.6 m
Problem 3: Highway segment is going under planning review. Given the following facts: Lane Width = 3.4 m Number of Lanes (N) - 2 (in cach direction) Total Lateral Clearance = 3.0 m Median No Median The 85th % Speed was found to be 100 km/hr (i.e. BFFS = 100 km/hr) PHF - 0.83 Terrain Type: Rolling You are asked to: A. Determine the maximum peak-hour volume that the segment can serve at a LOS C. B. Make suggestions on how to increase the total capacity while maintaining the LOS at C without major investments.
What super-elevation rate would you recommend for a roadway with a design speed of 110 kph and a radius of 1400 ft? Assume f=0.11.
During peak periods, “Trotro” drivers use the shoulders as travel lanes on the section of the Kasoa road approaching the toll booth from the West Hills Mall direction. As a Highway Engineer, what design intervention would you propose to prevent the shoulders from being used as travel lanes during congested period or as part-time shoulders but still function as shoulders? (CR,5)
Q2- Calculate the right of way of rural divided four-lane highway has a depressed median and it is constructed on embankment. The median width is 40 m. embankment height is 6m. lane width is 3.5 m.shoulder width is 2.5 m and side slope is 1:3 (VH)?
A highway section, +2% , meet -8%at point with 52.0 m( GTs) at speed 120 Km/hr. Determine the elevation of the highest point on the pavement surface within this section.
Determine the impact factor of the highway curve having radius of 1546 ftand maximum design speed of 51 mph.
C. Design a Two way - one lane Highway with the following specification. V - 90 kph e - 0.05 m. 15 m SD - 115 m wheel base - 2.25 m c- 3 Pavement is rotated at center | - 20° Determine the following: Minimum Radius Road Widening Transition Spiral (if any) Vertical Curve Tangent and Length of Curve Road Profile for horizontal alignment with station if the start station is 1 • 000
Wrong answer will be rated negative. The horizontal distance between its PVI and PVC is 150 meter. The elevation of PVI is 450.2 meter. The initial and final grades of the road are -4% and +3% respectively. Chainage of PVC is 1620 m. Based on the given set of information, determine the followings: i. Elevation of PVC. ii. The chainage of PVI. iii. Chainage and elevation of PVT. iv. Chainage and elevation of the lowest point of the sag curve.
For the following conditions: Design speed 60 mph, V/C ratio = 0.6, Level of service = Curve radius, 955 ft, Time value = $4/hr. If the basic section cost for passenger cars on a multilane highway is $206/KV-M, estimate the highway grade. B, %3D