Given an element with stresses as indicated in the figure below, use method of the Pole (only) to find: a) The major and minor principal stresses and the planes on which they act. b) The stresses on a plane inclined at 30° counter-clockwise from the horizontal. c) The maximum shear stress and the inclination of the plane on which it acts.

Given an element with stresses as indicated in the figure below, use method of the Pole (only) to find: a) The major and minor principal stresses and the planes on which they act. b) The stresses on a plane inclined at 30° counter-clockwise from the horizontal. c) The maximum shear stress and the inclination of the plane on which it acts.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
The stresses at a point in a bar are o1 = 28N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. O2 Axis of Major Stress 55°
Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown below. Using Mohr's circle determine the following quantities (a) the principal stresses and their directions and (b) the maximum shearing stresses and the directions of the planes on which they occur. 100 MPa 50 MPa 75 MPa 75 MPa 50 MPa 100 MPa
1) The state of plane stress at a point is shown on the element in Figure. Determine the maximum in-plane shear stress at this point. B 50 MPa ox Ox= -80 MPa = +50 MPa Oy Txy = -25 MPa 80 MPa 80 MPa A 25 MPa Ľ 50 MPa
Q 2: The state of stress at a point is characterized by the components:= [ 12 3 0 3 4 0 0 0 10Find the values of the principal stresses and their directions?
The stresses shown in the figure act at a point on the free surface of a machine component. If o= 45 MPa in the direction shown, determine the normal stress oy at the point. Ox 27 MPa 30° 50 MPa O-16.3 MPa O-19.5 MPa O-22.8 MPa O-17.2 MPa O -20.5 MPa
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
QUESTION 2 An element in plane stress is subjected to stresses; Ox , Oy, and Txy (FIGURE 2). Using Analytic method, determine the stresses acting on an element oriented at an angle 0. (Note: The angle 0 is positive when counter clockwise and negative when clockwise) i. Normal Stress (ox', oy ') ii. Normal Shear Stress (Txy') iii. Shear Stress Maximum (t max ) iv. Show the stresses on a sketch of an element oriented at the angle 0. 100 MPa 50 MPa 150 MPa 60° 150 MPa 150 MPa FIGURE 2
1. Given that the value of P on the figure below is equal to 15 kN which is applied to the centroidal axis of each segment of the rod which is made up of aluminum, bronze and steel which are rigidly connected. Determine the stress in each material in the rod. Steel A=300 mm2 Bronze Aluminum A=400 mm2 A=600 mm2 2P ЗР 4P P 3m+ 5 m 4 m-
Figure below shows the stresses on an element ABCD. Determine the sum of normal and tangential stresses (in MPa) on the plane EF inclined as shown in figure below. (Round off to two decimal places) 45 MPa 4 30 MPа 120 MPa - 120 MPa 45° E 30 MPa 45 MPa t
An element has a tensile stress of 600 N/mm2 and a compressive stress of 400 N/mm2 acting on two mutually perpendicular planes and two equal shear stresses of 100 N/mm2 on these planes as shown in figure. (by Mohr's circle аpproach) 400N/mm 100N/mm 600N/mm 600N/mm? 100N/mm 400N/mm (a) Find the principal stresses and maximum shear stress.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i