Find the question. Thanx. Given: A doubly reinforced rectangular concretebeam is subjected to a factored ultimate momentM,-1396 kN.m. Assume f= 28 MPa, 1,= 420MPa. Assume d = 75 mm, d= 700 mm, and b=380 mm. Design the section for this ultimatemoment. Consider that P =Pa.005 = 0.01806 assingly reinforced beam. Keep the draft of yourmaxcalculations with you; just fill your answers to thequestions shown below, and no need to send anyattachment.Check the capacity of the section if singlyreinforced, and calculate Mamax=kN.mWhat is the required area of tension steel A, (mm)?mmWhat is the required area of compression steel A',(mm)?mmWhat will be the compression steel (A) conditionat ultimate?

Answered: Image /qna-images/answer/241c7a70-7792-4635-9881-d26db1eec1d3.jpg

Given: A doubly reinforced rectangular concrete beam is subjected to a factored ultimate moment M=1396 kN.m. Assume f = 28 MPa, 1 = 420 MPa. Assume d = 75 mm, d= 700 mm, and b= %3D 380 mm. Design the section for this ultimate moment. Consider that Pma =Pa.0os = 0.01806 as singly reinforced beam. Keep the draft of your calculations with you; just fil your answers to the questions shown below, and no need to send any attachment. Check the capacity of the section if singly reinforced, and calculate Mamax kN.m What is the required area of tension steel A, (mm) A = mm What is the required area of compression steel A', (mm)? A', = mm What will be the compression steel (A) condition at ultimate?

Given: A doubly reinforced rectangular concrete beam is subjected to a factored ultimate moment M=1396 kN.m. Assume f = 28 MPa, 1 = 420 MPa. Assume d = 75 mm, d= 700 mm, and b= %3D 380 mm. Design the section for this ultimate moment. Consider that Pma =Pa.0os = 0.01806 as singly reinforced beam. Keep the draft of your calculations with you; just fil your answers to the questions shown below, and no need to send any attachment. Check the capacity of the section if singly reinforced, and calculate Mamax kN.m What is the required area of tension steel A, (mm) A = mm What is the required area of compression steel A', (mm)? A', = mm What will be the compression steel (A) condition at ultimate?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Let the allowable stresses in the post be ??? = 120 ??? and ??? = 6 ???. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Each steel bar has cross-sectional area of 900??2
For the beam shown below, determine the steel area required for the section shown below. The cross-section dimensions are limited to the values shown. If compression steel is required, assume that it will be placed at a distance 70 mm from the compression face. Assume f'c = 28 MPa and Fy = 420 MPa. The concrete is normal weight. Assume: Mu = 1000 kN.m. b%3D 300 mт. d = 550 mm. T70 mm b mm mm
Problem 4: A reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. Compressive reinforcement (if required) will be placed at d’ = 60mm. f’c = 25 MPa and fy = 415 MPa. The beam is to support a factored bending moment of 520 kN-m. φ=0.90. Use 2010/2015 NSCP. 1. Calculate the steel ratio for a balanced section2. Determine the governing steel ratio following NSCP requirements.
A beam having a width of 300 mm and a depth of 600 mm carries a dead load of 24 kn/m (including its own weight) and a live load of 32 Kn/m. The clear distance between the two supports is 5m. Use 75 mm as steel covering. Use fy=400 Mpa, f’c=21 Mpa. a. compute for the shear capacity of the concrete and what additional shear reinforcement strength is to be required by the steel. b. compute for the theoretical spacing needed for critical shear. Use 10mm diameter bar for shear reinforcement. c. compute for the maximum spacing needed for critical shear.
A rectangular beam has a width of 285 mm and an effective depth of 520mm. It is reinforced with 4 – 36 mm ø bars having fy = 430 MPa. If he compressivestrength of the concrete is 28MPa, find the following a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?
Given are the following: 600 Unit weight of concrete = 24 kN/m3 f'c = 35 Mpa fse = 1350 MPa 820 MPa fpu Aps = 1200 mm? = 1050 MPa fpy Beam is a simple span and have a length of 30m. Use bonded tendons as prestressed reinforcement. A. Determine the depth of the compression block (mm) B. Determine the nominal moment strength (kN-m) C. Determine the design moment capacity (kN-m) 150 150
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 8-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. The centroid of the bars are 70 mm from the concrete surface. Use f’c = 21 MPa and fy = 415 MPa. a. Determine the nominal compressive force on concrete only when the column is at balanced condition with bending about the strong axis. = [Cc] kN (whole number, ANS: 888) b. Determine the location of the plastic centroid from the left short side of the column. = [x] mm (ANS 200) c. Determine the ultimate axial load the column can sustain at balanced condition if the reduction factor is 0.65. = [Pub] kN (whole number, ANS 552).
Given are the following: 350 f'c = 55 MPa f pu = 1350 MPa Aps = 1500 mm? fpy = 1100 MPa Use bonded tendons as prestressed reinforcement. A. Determine the value of fps (MPa) B. Determine the depth of the compression block (mm). 008 00L
3. A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: a. Effective flange width of an interior beam in mm =____? ____ b. Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ____?____ c. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =____?_____
1. For the given singly reinforced beam section, fy =352 MPa, and f's = 28MPA. Calculate the required parameters for the different section condition in the table. d = 257mm h = 307mm 200mm Concrete Steel of Location Limit for No. of 16mm Area of diameter bar Condition Depth strain strain compression of block "a". neutral steel in to meet the axis "c". sq.mm. given beam condition. Units N/A N/A mm mm Sq.mm bars Balanced 0.003 Condition Compression 0.003 controlled Transition 0.003 controlled Tension 0.003 controlled
hinz 1. For the beam cross section below, determine the amount of steel As required to cause the strain in the tension steel & to be 0.005 just as the maximum strain in the concrete reaches 0.003. fc' = 3000 psi and fy = 60,000 psi. N.A. b= 10"- Cross Section d = 23" [7422 4233 134 S THE THE CALE DES 2 23-c me Like phans 0.005 PANE Strain 0.003 P HOME st 0.85f Stress 6 I.C. Nc NT * * * * * Delorme
A beam has a width of 350 mm and a total depth of 700 mm. The loading is as shown in the figure. Material strengths are fc’ = 32 MPa, fy = 400 MPa, and a stirrups diameter of 10 mm. Consider the spacing requirements a. Determine the numbers of 25 mm diameter for bottom reinforcement. b. Unity ratio of the designed section Show complete solution. Need ASAP. thank you.