A uniform rigid bar which weighs 1000KN/m is supported by a cable at point B, a rough surface horizontal floor at point A, and a corner edge of a rough surface wall at point C. If the coefficient of static friction on all contact surfaces is 0.10, determine the reaction at the supports of the uniform rigid bar. Neglect the weight of the cable. Figure, 2m E P = 1KN 2m

A uniform rigid bar which weighs 1000KN/m is supported by a cable at point B, a rough surface horizontal floor at point A, and a corner edge of a rough surface wall at point C. If the coefficient of static friction on all contact surfaces is 0.10, determine the reaction at the supports of the uniform rigid bar. Neglect the weight of the cable. Figure, 2m E P = 1KN 2m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o
A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass ofthe ladder is halfway along it. For the ladder to be in mechanical equilibrium: Write down equations for the total r- and y-components of the 5 forces acting on the ladder
A 200 lb block is in contact with a plane inclined at 30 degrees to the horizontal. A force P, parallel to and acting up the plane, is applied to the body. If the coefficient of static friction is 0.20, find: a. the value of P to just cause the motion to impend up the plane b. the value of P just to prevent motion down the plane c. the magnitude and direction of the friction force F if P= 80 lbs
20 cm The homogeneous block weights 250 N. Determine the value of P for which the block 30 cm in equilibrium, the coefficient of friction is 0.3 between the plane and the block. 15 cm 10 N 10 cm
Solve each of the following problems indicated below. Present your complete-detail solution including the free- body diagrams. (1) The maximum tension that can be developed in the cord show in Figure below is 500 N. If the pulley at A is free to rotate and the coefficient of static friction at the fixed drums B and C is u, = 0.25, determine the largest mass of the cylinder that can be lifted by the cord. Assume that the force T applied at the end of the cord is directed vertically downward, as shown. D B 45° C
Item 2 of 2 In figure shown, the mass of block A is 50 kg. The coefficient of static friction for all surfaces of contact is 0.12, determine the maximum mass of B to maintain equilibrium of the system. Assume the pulleys to be frictionless and use e = 80° and a = 50° of A 100
20 cm Q5: The homogeneous block weights 250 N. Determine the value of P for which the block 30 cm in equilibrium, the coefficient of friction is 0.3 between the plane and the block. 15 cm 10 N 10 cm 3 (20 Degree)