From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28

From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about pin A through an angle of 0.06°. Calculate the normal strain developed in wire BD. Answer: EnD = 0.0014 mm/ mm 300 mm B 400 mm
From the figure below, assume 8 K1 = K2 = 4 K3 = 2 K4 and that layer 2 and 3 are of equal heights. AB = 12 cm, BC = 18 cm and CD = 15 cm. All remaining units are also in cm. A B D K2 K1 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 4.60 x 10^-2 cm/s (IN 2 DECIMAL PLACES) 28 12
Bar AB is rigid and is attached to the steel and aluminum rods as shown in the figure. Before the application of load P, the rigid bar AB is horizontal. Determine the vertical displacement (mm) of point C caused by the load P = 50 kN. A Aluminum L = 3 m A = 300 mm² E = 70 GPa k 3.5 m C P -2.5 m Steel L = 4 m A = 500 mm² E = 200 GPa B
• The three steel bars shown in the figure are pin connected to a rigid member. If the applied load on the member is 15 kN, determine the force developed in each bar. Bars AB and EF each have a cross- sectional area of 50 mm2, and bar CD has a cross-sectional area of 30 mm?. Take Est = 200 GPa. B D F 0.5 m E - 0.4 m- 0.2 m 0.2 m 15 kN
Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area Wall thickness- 2mm b. Perimeter of the thin walled tube ABC is a sector with a radius of 50 mm c. Shear flow AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium d. Shear stress e. Angle of twist A R 90° в D 3R
•213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50KN, determine is vertical movement. ALUMINUM L=4m A=500mm? STEEL L=3m A=300mm2 E=200GPA E=70GPa 2m 3m
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER:
The cross section of a slit rectangular tube ofconstant thickness is shown in the figures.(a) Derive the following formula for the distance efrom the centerline of the wall of the tube in thefigure part a to the shear center S: e = [b(2h+3b)/[2(h+3b)] (b) Find an expression for e if flanges with the samethickness as that of the tube are added as shownin figure part b.
All Elements have a fixed value of E and I. Do load modelling for 1 meter strip width in the water tank section of wwwwww www.www the system.Draw the M N T diagram of the entire system. n=47 6 m. A ΔΒ B 7 water 8 m D 2 m. 47ton 3 m. E 1/10
Problem 5.2 The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b= 1 ft D -b 2b B E AG Check your work: FEF = 1.26 kips a a a a P
A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 13 ksi. Given: ly=/z=11.3 in 4 A=4.75 in² kmin = 0.983 in. 0.5 in. 1.43 in.- Mo C B 0.5 in. ✓ 5 in.- 1.43 in. The largest permissible value of the moment Mo is kip-in. 5 in.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and = 11.7 um Neglect bending of the beam. m°C A=640mm2 A=320mm2 A 1.2 m 0.8 m 1.2m 54KN What is the stress of rod C if there is no change in temperature in MPa?