Force Method 3 B The structure shown above has a rotational restraint only at A, and a fixed (clamped) support at B. In using the Force Method to determine all support reactions of the structure shown above, which of the support restraints can be chosen to be redundant: (Select all correct answers) Select one or more: Rotational restraint at A b. Rotational restraint at B D c. Vertical restraint at B Od. Horizontal restraint at B

Force Method 3 B The structure shown above has a rotational restraint only at A, and a fixed (clamped) support at B. In using the Force Method to determine all support reactions of the structure shown above, which of the support restraints can be chosen to be redundant: (Select all correct answers) Select one or more: Rotational restraint at A b. Rotational restraint at B D c. Vertical restraint at B Od. Horizontal restraint at B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

THE DIAGONAL MEMBERS IN THE CENTER PANELS OF THE TRUSS SHOWN ARE VERY SLENDER AND CAN ACT ONLY IN TENSION; SUCH MEMBERS ARE KNOWN AS COUNTERS. DETERMINE THE FORCE IN MEMBER DE AND IN THE COUNTERS THAT ARE ACTING UNDER THE GIVEN LOADING. (15 PTS) Counters ARA B F 6 ft H C E G 3 kips 6 kips 9 kips -S ft- <8 ft- S ft→|<-S ft-
Calculate the support reaction at roller support A
2. Find the force acting in Bar AC,CE & CD of the compound Truss and the reactions at A & F as shown in the below figure. 180 lb 540 lb 10 10 B D 10 A E F 18' RA RF
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
O (6) Facebook e.com/courses/7419/assignments/132721 Maps 国Reading WRITE YOUR NAME AND YOUR ID NUMBER. PLACE YOUR SIGNATURE AT THE LOWER RIGHT CORNER OF YOUR ANSWER SHEET DRAW THE FIGURE. PROVIDE COMPLETE SOLUTION. NOT FOLLOWING INSTRUCTION WILL GET ZERO. Determine the reaction at supports and compute the force in members: df, ca, cd, and cf (You may use any method.) Tabulate your final answers: MEMBER// FORCE, KN// COMPRESSION OR TESNSION 5m 130° 40KN 5m 5m 6m Show all 99+
4. Find the force acting in Bar AC,CE & CD of the compound Truss and the reactions at A & F as shown in the below figure. 180 lb 540 lb 10 10 D 10 A E F 18' RA RE B.
Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P = 5 kip are applied to the lever arm, Determine (a) the reactions at the fixed supports A and C and (b) the shear stress developed at a point located 1 in. from the center-line of the bar at a cross-section close to point A. 2.5 fi 2.5 ft 6 ft 4 in. 4 in.
4. Which of the following force diagrams correctly shows the reactions at the supports? A w R R R2.y w R R D C B.
Instruction: Please provide the given-required-solution and show the complete solution and the FBD. Problem: Determine the reaction at E and the force in each member of the right half of the truss.
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA
Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa. c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4. Use appropriate (SI) units as it applies (if any.)
B F RK E G F1 F2 AC, CE, EG, GI, IK, BD, DF, FH, HJ = 12.5 m, AZ=15 m, ZB=6.25 mF_1= 60 kN, F_2 = 60 kN For the truss as shown and the loading indicated. Show the free body diagram for the joint: Olncluded in manual solution ONot made 1.Find the reactions. pe here to search