For two row velocity compounded simple impulse turbine wheel derive the expressions for Diagram Power and Diagram Efficiency and also prove that : i. (P )max = 8 Cb? ii. ( na )max = Cos'ai %3D
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A: Given, P1=87KPaP2=3000KPaT1=20°C=293KFAD=0.22m3/minLD=1.3n=1.3N=1500rpm We know…
Q: A twin jet Pelton wheel is required to generate 750O KW when the available head at a nozzle is 400…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the…
A: 1. The isothermal efficiency is - ηiso = lnP2P1nn-1P2P1n-1n-1ηiso =…
Q: An inwared flow reaction turbine develops 130kw under a head Bm. The flow Velocity is 4mis and The…
A: Given data: Power developed, P = 130 kW Head of the turbine, h= 5 m Flow velocity of the turbine,…
Q: 11. A turbine of 9000 B.H.P. is working under a head of 25 m and runs at 100 R.P.M. What will be the…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A: Dear student, there is too much additional data in this question which is not required to calculate…
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A: Free air delivery is measured at - 101.325 kPa and 288 K The mass delivered is -m = PVRT =…
Q: In a stage of Parson's reaction turbine, the mean diameter of the wheel is 1.05 m and the speed is…
A: The answer is given below
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the…
A:
Q: A radial flow reaction turbine has the following characteristics: Circumferential area at entrance…
A: Ac1=258 cm2 or 258×10-4 m2Ac2=180 cm2 or 180×10-4 m2Q=.1 m3secηT=.82r1=25 cm or .25 mr2=12.5 cm or…
Q: A Kaplan turbine produces 16000 kW under a head of 20m, while running at 166 rpm. The diameter of…
A: Given:P=16,000 KWH=20 mN=166 rpmDo=4.2 mDh=2 mQ=120 m3/s
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: he nozzle is 550 m/sec. For mass flow rate of 3300 kg/hr and for axiai exit conditions. Find (1) The…
A:
Q: 17. Find the maximum power produced by a Pelton wheel. The jet diameter is 10.45 in and the…
A: Given data Jet Diameter = 10.45 inch = 0.26543 mAvailable Head = 2200 ft = 670.56 mWe have to find…
Q: An axial flow turbine is operated at a pressureof 24m and develops 24,2MW when rotating at 146…
A: GivenP=24.2 MWN=146 rpmDb=2.1 mDo=4.72 mηh=94%ηo=88%
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: he date for a certain installation are as follows Net Head = 454 m, BP = 57,200 bkw, n = 750 rpm,…
A: Given:H=454 mP=57200 KWN=750 rpm
Q: Q. The velocity of steam at inlet to simple impulse turbine is 1000 m/s and the nozzle angle is 20%.…
A:
Q: In a Parson reaction turbine, the angles of receiving tips are 35º and of discharging tips 20º. The…
A: Blade speed , u = 125 m/s take a scale 5 cm = 125 m/s 1 cm = 25 m/s from the velocity triangle:…
Q: The first stage of a turbi and 400 "C is expanded 700 m/s. The inlet velocit 18°; first row blades…
A: INTRODUCTION : Turbines are the prime movers in which the heat energy of the steam is converted…
Q: The centrifugal pump of Fig. develops a fl owrate of 4200 gal/min of gasoline at 20°C with…
A: Given: Speed of the blade = 1750 rpm flow rate, Q=4200 gal/min=4200×0.133681×160=9.357 ft3/s…
Q: 10.25 For a flow rate of 12 L/s and turbine speed of 65 rpm, estimate the power transferred from the…
A:
Q: In a certain stage of an impulse turbine, the nozzle angle 20° with the plane of the wheel. The mean…
A: Given details: Mean diameter(D)=2.8 m Nozzle angle(α)=20 power(P)=55 kW Speed(N)=2400 rpm…
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A: 1 2
Q: Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200…
A:
Q: The following particulars refer to a two Tow velocity- compounded impulse wheel which foame Q. the…
A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: A turbine runs at 150 rpm, discharges 5.7 m3/s and develops 1200 bkw under a net head of 25 m. If…
A: Given data: N=150 rpmQ=5.7 m3/sP1=1200 bkwH1=25 mHn=40 m Need to determine the break power.
Q: : Derive an expression for the maximum blade efficiency of reaction turbine.
A:
Q: A twin jet Pelton wheel is required to generate 7500 KW when the available head at a nozzle is 400…
A: Answer: The total flow rate is 2516 lit/sec. Hence, the correct option is (A).
Q: a. What is the difference between impulse turbine (a Pelton wheel turbine) and a reaction turbine…
A: Impulse turbine has a rotor that rotates by using only the kinetic energy of the fluid jets…
Q: lbert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: PROBLEM: A double-overhung impulse-turbine installation is to develop 15,000 bkw at 257 rpm under a…
A: Data given- H = 340 m P = 15000 kw N = 257 rpm
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: Question Find the air-standard efficiency and expansion ratio of a Diesel engine if the clearance…
A: It is a type of internal combustion engine in which the burning of diesel fuel in the cylinder is…
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: with the axial A Kaplan turbine operates at (45 rpm) with a blade peripheral velocity of (14 m/s).…
A: Given: The speed of the Kaplan turbine→N=45 rpm Blade peripheral velocity→u=14m/s Inlet blade tip…
Q: In a gas turbine engine (A, = 2.85 A2, pi = 1.14 p2, p1 = 100.5 kPa, T1 = 11 °C, V1 = 107 m-s1, v2 =…
A:
Q: find peripheral velocity and discharge.
A:
Q: A remote community in Marikina plans to put up a small hydro-electric plant to service six closely…
A:
Q: Suppose that the pump of Fig. is run at 1100 r/minagainst a pressure rise of 210 bar. (a) Using the…
A: Given:Pump speed,n=1100r/minPressure rise,∆P=210 bar
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A:
Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…
A: given; ⇒initial condition;⇒pressure(P1)=87KPa⇒temperature(T1)=200c=293K⇒free air delevery or initial…
Q: PROBLEM: The data for a hydroturbine installation in Fionnay, Switzerland are: H, = 454 m, BP =…
A: Given dataHead H = 454mBrake power BP = 57200bkWSpeed = 750rpmEfficiency of the turbine ηT = 90%To…
Q: In a parson's reaction turbine, mean blade speed is 60 m/s. Inlet conditions of steam are 3 bar and…
A: The answer for this is in the next steps
Q: Problem (5.1) An impulse turbine is supplied with steam at a pressure of 1.6 MPa and temperature of…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 5 images
- Ans. [391.67 kW, 61.13 %] Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 m/s. The nozzles are inclined at an angle of 16° to the plane of the wheel. The blade velocity coefficient is 0.72, calculate the blade efficiency, work done and also estimate the energy V?. lost in the blades as; m° (-2).Take the blade angles at inlet and 2 outlet =25°. Ans. [76%,105 kW, 27.072 kW]Q2//The rotational-speed of an impulse turbine wheel is 3000 r.p.m. The nozzles are inclined at 20° and their efficiency is 0.89. The isentropic heat drop for the stage is 159 kJ/kg. If the blade speed ratio is 0.4, the blade speed coefficient is 0.82, and the blade efficiency is 0.76. Find for steam flow rate of 15 kg/s: 1. The mean blade ring diameter. 2. The power developed by the stage. B = 32.4°:Be : 38.5°). %3D %3D Answer (1.355m, 1613.2 kW,B: Whal are Objects Q4: A: Derive an expression for the maximum blade efficiency of reaction turbine. R: Exnlain and draw the water circulation in H.P. steam power plants?
- Gas Compressors 14.5 Find the cylinder dimension of a single-cylin der, double acting compressor handling 28.32 Its/revolution of air from 99.975 Kpaa to 723.954 kPaa. Compression and reexpansion are in accordance with p35 = C. Use the conventional volumetric efficiency; c = 5% and L/D =1. Ans. 26.77 x 26.77cmYou have invented a hydrogen‐fueled turbine engine that operates between a combustion temperature of 2500. K and an exhaust manifold temperature of 500. K. How much work does it produce per kilojoule of fuel energy if it operates at 75% of maximum theoretical efficiency?Q. A single stage impulse rotor has a blade ring diameter of 57.5 cm and rotates at a speed of 10,000 r.p.m. The nozzles are inclined at 20o to the direction of motion of the blades and the velocity of the issuing steam is 1,050 m/sec. Determine the inlet blade angle. Assume a friction coefficient of the blading equal to 0.85 and that the inlet and outlet angles are equal. Find also: (a) the power developed at the blades for a steam supply of 1,350 kg per hour (b) the diagram efficiency, and (c) the loss of kinetic energy due to blade friction
- 1.4 A diesel engine operating an air standard diesel cycle has 20cm bore and 30cm stroke. the clearance volume is 420cm3. if the fuel is injected at 5% of the stroke, find the air standard efficiency. 1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1V2 and the expansion ratio r, = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion. %3DWhat is the turbine output of 100m head and delivering 1 cu. m/ sec in a hydro electric power plant if turbine efficiency is 88%?An Otto engine has a clearance volume of 7%, it produces 300 kW of power in a minute. Find: Compression ratio heat added in kW heat rejected in kW Volume displacement if volume at point 1 is 0.1 m³ mean effective pressure in kPa Thermal efficiency, %
- Provide complete solution and detailed diagram. A steam turbine has an inlet enthalpy of 2700 KJ/kg and speed of 120 m/s. If exhaustenthalpy is 2500 KJ/kg, find the exit speed. A. 763.45 m/s B. 342 m/s C. 934 m/s D. 644 m/s(2) a fou-cylinder, 2.4 liter engine operates on a four-stroke cycle at 3200 r.p.m. the compression ratio is 9.4:1, the connecting rod length r = 18 cm, and the bore and stroke are related as S = 1.06 B. calculate :- 3 (a) clearance volume of one cylinder in cm³,L, and in ³. (b) Bore and stroke in cm and in. (c) Average piston speed in m/seca 1 ft/secA gas turbine cycle is preferred over steam power plant in power station that is used to generate electricity. Your manger asked you to investigate and study the possibility of upgrading the power plant discussed in Project-1 to a gas turbine cycle or a combination of both cycles (Combined cycle). The head of the department asked you to deliver a report showing a professional evaluation and assessment for gas turbine cycle efficiency given the following information.First you selected a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications:• A pressure ratio of 10.• Heat is added to the cycle at a rate of 500 kW• Air passes through the engine at a rate of 1 kg/s• The air at the beginning of the compression is at 70 kPa and 0 C.