For the water distribution system given below, the final corrections are applied and the flow distribution is balanced: 1. Find the missing data in the table. 2. Find QB and QD 3. Find the pressure at A, if the pressure at B is 100 kPa. Line Length Diameter Ch Q V L 25 m³ (m) (m) (m) m³/s (m/s) AB 500 120 8.1 ? ? BD 500 120 ? ? 1.39 AD 800 100 ? ? ? 300 250 ? QD D B QB

For the water distribution system given below, the final corrections are applied and the flow distribution is balanced: 1. Find the missing data in the table. 2. Find QB and QD 3. Find the pressure at A, if the pressure at B is 100 kPa. Line Length Diameter Ch Q V L 25 m³ (m) (m) (m) m³/s (m/s) AB 500 120 8.1 ? ? BD 500 120 ? ? 1.39 AD 800 100 ? ? ? 300 250 ? QD D B QB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.5 Determine the volumetric flow of water in m3/hr flowing in a pipehaving a diameter of 40 mm through an orifice having a diameter of 20 mm.Manometer reading across the tapping is 15 cm of Hg. Assume correctionfactor = 1. Reynolds number Ra is 105 . Assume density of water = 1000 kg/m3and kinematic viscosity is 10–2 stokes (cm2/sec). Also calculate the pressuredifference at the tappings. Assume Cd = 0.61.
The rectangular channel is 2 m wide, and the depth of the water is y₁ = 1.6 m as it flows with an average velocity of V = 0.6 m/s. (Figure 1) Figure < 1 of 1 Part C Determine the required height of the bump so that the flow can change to rapid flow after it passes over the bump. Express your answer to three significant figures and include the appropriate units. h= Submit Part D ■μÀ 1 Value Y2 = Request Answer What is the new depth y2 for rapid flow? Express your answer to three significant figures and include the appropriate units. " Submit μA Value Units Request Answer O ? Units Revi
Subjact: Data: An inverted u tube manometer is connected to two horizontal pipes A. and 8 threugh which water is flowing The vertical distance between axes of the se pipes is 30 cM When an oil SG=0.8 îs uced as a Jauge fluid, the vertical heigh 1s of water columos in the two limbs are found to be the same and equal to 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. C. 30 cm 35 cm 35cm tw ater 30cm water
Water at flows in the system shown. The density of the water is 1.94 slugs/ft', and the viscosity is 2.359x10 slugs/ft-s. Determine the following. a. Q ignoring minor losses b. Q accounting for minor losses Kt 0.5 10 ft IK,- 10 D= 3 ft L= 1000 ft eps = 0.00164 ft Q = ? Ka= 1.0
For fig shown if water flow rate is 60 lit/'s, Find (h) Note that Density: Pwater = 1 kg/m Pair= 1 kg/m %3D D, =5 00mm Water a.5m water 25cm Can you answer ickly? Bernoulli's Equation
Example 2: Water flows along the drainage canal having the properties as shown below. S, = 1 ft/500 ft. Estimate the flowrate. 3 ft 2 ft→ 3 ft n3 = 0.030 n = 0.020 (3) (1) 0.6 ft| n2 = 0.015 0.8 ft (2)
Example 12.2: For turbulent flow in pipes (smooth as well as rough) show that Vmax = 1.33√f +1 V
Problem 2: Manometer and Pipe S = 0.8 300 mm dia Water flows past a manometer as shown. The manometer fluid is oil with s = 0.8. If the manometer reading Rm= h = 0.12 m, what is the water velocity at the centerline of the pipe?
There is a leak in a horizontal 30 cm pipeline (f= 0.025). Upstream from the leak two gages 600 m apart on the line show pressures difference of 140 kPa. Downstram from the leak two gages 600 m apart show a pressure difference of 126 kPa. How much water is being lost from the pipe? a.5 L/s b.11 L/s c.9 L/s d.7 L/s PLEASE INCLUDE FIGURE OR FBD
A fluid flows downward with the rate of Q=0.015 m/s in a smooth vertical pipe with the length of l. (a) Find the diameter of the pipe if the pressure drop (pi – p2) is zero. (Hint: Use Moody Chart with the initial guess of f=0.02. Two iterations are enough) (b) If the pipe outflow hits a fixed vane as shown in the figure, what would be the horizontal and vertical forces (Fx, Fy) on the vane? (p = 1000 kg/m3; u = 0.001 kg/m. s; a = 30 deg)
For the pipe network given in the figure, the pipe flow rates in the intermediate lines, the given initial values Calculate using the Hardy-Cross Method. (Take the coefficient of friction on all lines f = 0.002 and perform two iterations.) Hat no 1 2 3 4 5 150 lt/s Q (It/s) 100 50 10 75 15 1 2 L (m) 300 300 200 250 150 3 35 lt/s 25 lt/s D (mm) 100 125 150 125 200 4 5 90 lt/s
Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line to the figure below. Enter the corresponding numbers in the table. Assume steady incompressible flow from left to right. At point A, the pressure head P/y = 23 ft and the velocity is V=8 ft/s. The pump adds AH = 16 ft. Ply V²/(2g) EGL HGL EGL and HGL [ft] >> EGL_HGL(2,1,2,'-','P',20,'ft') A D, 2 ft B C D₂ = 1 ft D E D₂ = 2ft F 30 T TI 25 20 5 10 0 5 A A 10 B F 15 20 x [1000 ft] C 25 D 30 E F