For the frame and loading P = 480 lb shown, determine the internal forces (axial for of the structure indicated. (Round the final answer to the nearest whole number.) E A 2 in. 4 in. B 4 in. The axial force Fis The shear force Vis The bending moment Mis D 2 in. 2 in. lb. ← lb. ↑ 4 in. lb-in. acting in the (Click to select) direction...

For the frame and loading P = 480 lb shown, determine the internal forces (axial for of the structure indicated. (Round the final answer to the nearest whole number.) E A 2 in. 4 in. B 4 in. The axial force Fis The shear force Vis The bending moment Mis D 2 in. 2 in. lb. ← lb. ↑ 4 in. lb-in. acting in the (Click to select) direction...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 01 The figure shows a truss which is pin connected at C and supported by a roller at D. It carries a vertical loads of 200 kN and 100 kN at joints A and E respectively. State if it is tensile or compressive. 4m D 2m A. E 200 kN 100 kN 6m 3m OCalculate the force in member DE. 2Calculate the force in member BE. 3 Calculate the force in member BC.
2.54 The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x 10-3. What is the length of the gap A? The cross-sectional areas are 300 mm? for rod AC and 250 mm² for rod BD. Use E = 200 GPa for steel. A B 0.75 m -1.5 m 2 m FIG. P2.53, P2.54
2.69 The bars AB, AC, and AD are pinned together as shown in the figure. Hori- zontal movement of the pin at A is prevented by the rigid horizontal strut AE. Cal- culate the axial force in the strut caused by the 10-kip load. For each steel bar, A = 0.3 in.? and E = 29 × 106 psi. For the aluminum bar, A = 0.6 in.² and E = 10 × 106 psi.
The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 = P2 = 4 kN, the force in member (CB) is equal to. %3D A 30° 30° OC E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression C. 2 kN - Tension d. 8 kN - Tension
Find the deformation of the bar in the figureE= 200gpa
The beam is subjected to a shear of V= 2 kN. What is the average shear stress developed in each nail? if the nails are spaced 75 mm apart on each side of the beam. Each nail has a diameter of 4 mm. The N.A is located on 137.5 mm form the bottom of cross section. The second moment of inertia about N.A is 63.5417*10^(-6) m^4. 75 mm 50 mm 75 mm 200 mm 25 mm 200 mm 25 mm 442.62 MPa
3 Determine the support reactions o- the beam shown here: 9 = 150 น max A + 12 hint: 1 resultant force is the area the Loading. 2 the point of action of resultant is not at the middle. ft. 10/ft B + under У
Q3/The tension AB in the truss as shown in the figure below, is 100 N. Draw the free body diagram and determine the magnitude of force in member CD&AD. Which members can say zero force members? B 2 m 30° 3 kN 2m 1 4 kN 2m 2 m H
6.2 Use the method of joints to calculate the force in each member of the loaded truss illustrated and state whether each memb er is in tension or compression. Also calculate the reaction forces al A and C. 2 m 2 m 60 2 m 1000 N FIGURE P6.2
Compute the forces in hars AB, AC, DF and DE in the scissors truss shown below: 12 Kips F 12 Kips B D 12 Kips 10 C (T/ H 12 kips G 12 Kips H 48 10²✨ 10² … 10¹. 10² × 10² J th
Using the method of joints, determine the force in each member of the truss shown below (solve for FAB, FAD, FBD, FDE, FBE, FBC, and FcE. Use the sign convention of negative for compression of the joint and positive for tension of the joint. 2000 lb -12 ft- 1000 lb 12 ft cl 8 ft D E -12 ft 6 ft 6 ft Hints: 1. The reaction at the roller support at E is 10,000 lbf upwards. 2. The reaction of the support at C is 7,000 lb, downwards.
An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 680 mm² and an elastic modulus of 29 GPa. Bar (2) has a cross-sectional area of 1580 mm² and an elastic modulus of 15.2 GPa. Determine the deflection of point A relative to support C. 70 KN 0.85 m O -1.902 mm O-2.101 mm O -2.250 mm O-1.354 mm O -2.879 mm 90 kN (1) 90 kN B (2) 1.15 m