For the compressor with the below details, determine the stroke, bore, and the power required for the motor drive the compressor at speed 1000 rev/min, considering the mechanical efficiency of the compressor is 85% and the motor transmission is 90% . L (Stroke) Inlet air Delivery air V = 25 m³/min P2=25 bar, P1=1.013 bar d(bore) T1 =288 K T2 =450 K Vc Vc Take L/d = 1.5 and Vc = 0.05V, PISTON

For the compressor with the below details, determine the stroke, bore, and the power required for the motor drive the compressor at speed 1000 rev/min, considering the mechanical efficiency of the compressor is 85% and the motor transmission is 90% . L (Stroke) Inlet air Delivery air V = 25 m³/min P2=25 bar, P1=1.013 bar d(bore) T1 =288 K T2 =450 K Vc Vc Take L/d = 1.5 and Vc = 0.05V, PISTON

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

asap
Displacement (c): 0.2 in3/revShank diameter (d) = 0.625 in.Piston diameter (D) = 1.5 in.Rotation speed (n): 1725 RPMPressure (P): 600 PSIStroke (L) = 18in. a) Calculate the theoretical flow rate of the pump in in3/min and US GPM.Theoretical flow (Q) = Theoretical displacement (C) x Speed of revolution (n)Theoretical flow (Q) = 0.2 in3/rev x 1725 rpmTheoretical flow (Q) = 345 in3/min = 1.49 US GPM b) Calculate the cylinder output speed in in/s.Cylinder output speed (VS) = Piston side flow (Q) / Piston area (Ap)Cylinder output speed (VS) = (Displacement x Speed of revolution) / Piston area (Ap)Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = 196.02in/s = 196.02 / 60s = 3.20 in/s Questions: c) Knowing the output velocity (ram speed), calculate the rod side flow in GPM when the ram is extending. d) Calculate the piston exit time in seconds. e) Calculate the piston entry time in…
A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%
Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
MECHANICAL ENGINEERING POWER PLANT ENGINEERING 2 A single stage, single acting air compressor running at 650 rev/min, has a bore of 350 mm and a stroke of 350 mm. The clearance volume is 5% of the swept volume. The inlet pressure and the temperature are 85 kN/m2 and 35EC. The delivery pressure is 750 kN/m2. Assume the index of compression is 1.3. Calculate: (i) The Volume induced (ii) The Volumetric efficiency (iii) The Indicated Power
B. Given: Cylinder Diameter = 95 mm Displacement Distance = 110 mm Pressure Ratio = 8.72 P1 = 145 Kpa T1 = 26 Degree Centigrade Mechanical Efficiency = 78% Solve: Suction Volume, Mass Flow Rate, Work Done and Shaft Power N = 1350 RPM
b) A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C, determine the free air delivered in m/s.
A 6inx10in in direct acting duplex pump with 1.5inches in piston rods make 35 double stroke percylinder per minute and delivers 135gpm of 100°F water against a total head of 460ft. The steamis supplied to the steam end at pressure of 150psig and exhaust to the atmosphere. Amount ofsteam supplied is 3800lb per hr at 0.98 quality; barometer is 20.6inHg. Assume that the pistonmake full stroke. Find the piston displacement of the pump in cm3/sec.
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised power required? Select the correct response: 29.32 hp 20.19 hp O 24.37 hp 29.41 hp 34.23 hp 30.37 hp lenovo
Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor? complete soln tnx.
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.