i Ii. In. 3 * e9:Y.2.73.2For the circuit shown in figure.For the circuit shown in FigureIf IB 40 MA , VBB= 6v,RE =I K2, B=80RcRgVecVBBRE..The value of IE is . ..4.24 O2.0241.243.245.246.24II

Given that IB= 40 μ A VBB = 6V RE =1k ohms β = 80

Answered: For the circuit shown in figure. For…

For the circuit shown in figure. For the circuit shown in Figure If IB 40MA, VBB= 6v, RE =1 Ks, B=80. %3D Rc Rg Vec VBB RE *..The value of IE is . mA 4.24 O 2.024 O 1.24 O 3.24 O 5.24 O 6.24 O ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
A chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A single phase bridge type full wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L / R) >> T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below Re given. V,) = 311sin(2750r)V| Note: T= 0.02s is the period value of the voltage source. R and L values do not matter in solving the problem. A; What is the value of the overlap angle in radians? B; Find the effective value of the output voltage
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
Given the circuit design for a Zener diode regulator in the previous question, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
For the ideal-diode clipper circuit given below, VS = 12.sinwt V. a. Determine the output voltage Vout and sketch this function. b. Remove the short circuit between points x and y, and replace it with a 2k2 Resistor. Find the range of values of VS for; D1 and D2 are OFF D1 is ON and D2 is OFF D1 is OFF and D2 is ON Is it possible for both D1 and D2 to be ON? y 1kO 3V D2 VS 3kQ. Vout D1 6V
Design a Zener diode circuit to regulate a source voltage that can vary from 9 VDC to 17 VDC, has a load current that can vary from 0 mA to 500 mA to generate a constant load voltage of 5 VDC. Draw the complete circuit with all values, determine the largest value of the inline source resistance (Rs), and determine the Zener diode's max power dissipated. Pzmax = Rsmax =
A designer has a supply of diodes for which a current of 2 mA flows at 0.7 V. Using a 1-mA current source, the designer wishes to create a reference voltage of 1.3 V. Suggest a combination of series and parallel diodes that will do the job as best as possible. How many diodes are needed? What voltage is actually supplied?
4. A voltage regulator circuit is shown on the right. The resistor value is chosen to obtain an output voltage (across the diode) of 0.7V. Use the diode small-signal model to determine the change in the output voltage when the supply voltage, V+, changes by IV. (This quantity is known as the line regulation and is generally expressed in mV/V) Hint: The answer will be only a function of V+ V+ ▷ R + Vo
Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. iii. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the rectification); the peak value of the output voltage considering the drop across each diode, the average voltage, iii. The current through the load resistor, The current diode, The frequency of the output signal, Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch…
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.