For Beam AB (EI Constant), use the Unit Load Method to Determine:1. The Deflection at C2. The Rotation at Support A.6 kN/m3m3 m

Answered: Image /qna-images/answer/c63d27cb-6f14-4c2e-909a-001b1fcc9a61.jpg

Answered: For Beam AB (EI Constant), use 1. The…

Engineering

Mechanical Engineering

For Beam AB (EI Constant), use 1. The Deflection at C 2. The Rotation at Support A.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.16P: A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable...

See similar textbooks

Related questions

Q: HiW. Find the deflection distribution dingram for the followsing laaded beam.

A: The beam is as shown below, RA=RB=5 N,

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1500…

Q: Using moment-area method, determine the angle of rotation and deflection 10 ft from “A”. EI is…

A: Given: To find: Angle of rotation and deflection at 10ft from A

Q: 03) The experimental data for the cantilever shown was given in table Find the modulus of elasticity…

A: Given Data - Cantilever Beam subjected to point load at free end Deflection due to point load ∂=2.87…

Q: 2. Using the conjugate beam method, determine the maximum deflection of the beam. Use E = 10,000 ksi…

A: When an amount of force act at the ente beam, then the bending produce in the beam due to the act of…

Q: A simply supported beam having constant EI throughout its geometry is loaded with 3P and P at point…

A: When a beam is subjected to a load, it will face reaction forces at the support and it tends to…

Q: Find the vertical deflection at point B.

A: Solution is given below.

Q: * For the RIGID beam shown, find the :deflection at point B 50 kN A B C 2m 3m 3m +0,025 m ID

A: Value of EI is needed

Q: The cantilever beam AB shown has a rigid bracket AC attached to its free end. Find the ratio a/L…

Q: Consider the maximum allowable vertical deflection of point D. Calculate the corresponding angle of…

A: Given data: From previous part, ◆ The torque acting on the shaft at B: T = 111600 lb•in ◆ The total…

Q: Using the double-integration method, find the deflection C and the slope at B. Assume that EI is…

Q: Find deflection at point B. A B a

A: The deflection at point B is given by the formula;→YB=WL33EIwhereW=Point Load=PL=length=aE=young's…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1960…

A: (a) The beam deflection at point A : VA = 0.92745 in. (b) The beam deflection at point B : VB =…

Q: 15 kip*ft 12 in 10 in 6 ft

Q: Determine the equation of the deflection for the cantilever beam shown. Then, calculate the slope…

Q: middle of AB using the Castigliano me

Q: beam. El is constant. Determine in terms of EI, the deflection at point B. 20 kN 40 kN/m B 8 m 3 m

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 27000 ksi; / = 450…

Q: Find the deflection at point A.

Q: alion the elastic portion Ab 0I the beam, b) Please find the slope at A, c) Please find the slope at…

Q: If w = 25 kN/m., calculate the value of EIδ at 1 m. of the free end of the loaded beam as indicated…

Q: A beam AB of span 6 m is simply supported at the ends A and B and is loaded as shown in figure. If E…

A: Draw the free-body diagram of the given beam.

Q: Calculate the vertical component of reaction support at point A (i.e., Ay) for the loaded beam shown…

A: Given:

Q: For the beam shown, use superposition and find a) maximum deflection in beam, and b) deflection at…

Q: 2Mo B Mo -

A: Given:- Length = L Deflection is the load applied to the body and undergoes deformation.

Q: ompute the slopes at A and C and the deflection at D for the beam shown in Q.2. Also, locate and…

Q: For the beam shown find the deflection at point B ft and D ft if El=2200kip.ft? by using the…

Q: Q4/ By using Double - Integration Method, find the deflection and rotation at point (C) of the beam…

Q: The simply supported prismatic beam AB carries a uniformly distributed load w per unit length in…

A: Draw the free body diagram of the beam: Calculate the reactions: Since the beam is symmetrically…

Q: C) Ose Castigtion's theorm to find vertical deflection in pant ca) for the beam shown below,…

A: Given data: The modulus of elasticity is E=200 GPa=200×103 MPa The inertia of the beam is I=300×106…

Q: 3. Find the angle of rotation BA at the left-hand, the deflection under the downward load, and the…

A: Calculated angles of rotation at point A .and deflection at load P and deflection at mid point of…

Q: Using Double Integration Method, find: a) Equation of the Elastic Curve Slope at point C b) c)…

Q: AB beam is a W section drawn profile, P= 50 kN, L= 1,25 m ve E= 200 GPa since it is ( Iw= 26,9.106…

Q: CON SIDER A BEAM CLAMPED ON DNE END TORSION AND A TOR QuE IS APPLIEO ALONG THE LENG TH OF THE BEAl.…

Q: the equation of the deflection for the cantilever beam shown. Then,

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A: Given: Total length of a cantilever beam, l =5 m Beam is subjected to two uniformly distributed…

Q: 03 The experimental data for the cantilever shown was given in table Find the modulus of elasticity…

A: As per given question Given data Weight =3N Deflections =2.87mm We have to determine modulus of…

Q: The cantilevered beam is subjected to a moment applied at its end El is constant. Using…

Q: The cantilever beam consists of a W530 × 74 structural steel wide-flange shape [E = 200 GPa; I = 410…

A: When a beam having length 'L' is subjected to a uniformly distributed loadω over the whole length of…

Q: A For the RIGID beam shown, find the :deflection at point B 50 kN B C 2m 3m ID 3m No deflection O…

Q: * Given the FLEXURAL RIGIDITY of the beam shown=6000 KN.m^2, find the deflection :at the roller…

Q: 60 k 3 k/ft A В -10 ft- -10 ft- -10 ft- El = constant E = 29,000 ksi I =4,000 in.4

A: Cantilever beam Cantilever beam is defined as the beam in which it contains fixed support at one end…

Q: (a) Find peak intensity q,if the deflection at joint Bis known to be 0.18 in. Assume that modulus E=…

A: This is a case of cantilever beam on which load is uniformly distributed. maximum deflection=…

Q: (Situation no. 2) For the beam supporting the loads shown with E= 200000 Mpa and I=1x10^8 mm^4. (4)…

A: Given data, Young's modulus, E = 2×105 MPa = 2×105×106 Pa Moment of inertia, I = 1×108 mm4 =…

Q: As indicated below, determine the value of deflection at the right end of the beam. 400 m 400N .Am.…

Q: Compound beam ABC is loaded by pointload P 51.5 kips at distance 2a/3 from point A anda triangularly…

A: given; lets take reaction force at A=RAlets take reaction force at…

Q: A steel cantilcver wall projecting Š megers is logded with. from a IS unitormly distributed of 20…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

For Beam AB (EI Constant), use the Unit Load Method to Determine:
1. The Deflection at C
2. The Rotation at Support A.
6 kN/m
3m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the beam at A, and (b) the deflection Vmidspan of the beam at midspan (i.e., x = 2.45 m). Assume a constant value of El = 1270 kN-m² for the beam; M₁ = 9 kN-m, wo = 19.8 kN/m, LAB = 1.1 m, LBc = 2.7 m. MA A Answer: (a) VA = (b) Vmid i LAB i Wo B LBC mm. mm.
Find the slope and deflection equations for the beam shown. Determine the rotationfrom point C. The unit of measure "t" means ton, 1 ton = 9.81 kN. Loaddistributed is vertical, downwards. EI = constant. Double Integration Method.
BP4: A simply supported beam of constant El and length L is supporting a distributed load omega w over half of its length from 0 to L/2. Determine the deflection of the beam at L/2 using Catigliano's method.
(use EI constant for whole span). A 10-meter-span, propped beam (fixed at the left support and roller at right support), with a uniformly distributed load from left support to six meters to the right, with a magnitude of six kilonewton per lineal meter, a downward concentrated load at the midspan. Solve the reactions at the fixed support and roller support, slope and deflection at the roller support, using Area Moment Method. Use the concentrated load as 24 kN.
3. Calculate the slope and deflection at the 60-kNm couple on the structure shown in the accompanying illustration. Use: a. Moment Area Method, b. Conjugate Beam Method 4 kN/m Fixed Hinge 60 kNm 5 m -5 m 5 m -5m I=1.46 x 10° mm". E=200000MPa Activate Windows so to Settings to activate W ndows.
Calculate the support reaction at A and B for thve beam shown in the fiqure below Take F 700 N. 3M 1M By Reaction force at point B By UN. Reaction force at point A N. Ay=
The simply supported beam carries a uniformly distributed load over parts of its length. Compute (a) the midspan slope and deflection, (b) the slope and deflection at point C. Segment AC’s beam property is worth EI and segment BC’s beam property is worth 2EI. E = 200 GPa, I = 80x106 mm4. Solve problem using the Area Moment Method.
L = 4 P=4 Solve the following beam structure using the direct stiffness method to obtain the B.M.D P ton P ton 2 toy'm 2EI 3EI K-EI Lm
Alt Gr Ctri 2. The force P is acting onto the beam ABC through the rigid arm BD. Considering the effects of P at the point B and using Singularity Functions determine the deflection of the end point C. (EI is constant for ABC). D L/2 L/2 SHOT ON MI 6 MI DUAL CAMERA
Cantilever beam is loaded by three concentrated forces. F, 1 Given: 11= 1Ocm; 1 2 = 25cm; 1 3 = 19cm; F1 = -0.2kN; F , = -0.6kN; F 3 = -1.6kN . Find: algebraical value of reactive moment (in N m) applied at fixed point (considering counterclockwise direction as positive and clockwise as negative). Answer:
Find the deflection of the beam in the middle of AB using the Castigliano method.
A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its centre. The cross-section of the beam is 160 mm wide and 270 mm deep. If E for the beam is 70x109 N/m2, the deflection at the centre is