For an AM superheterodyne receiver, station A with RF signal of 1000 kHz uses high side injection to receive the signal. A tuned circuit for a bandpass filter has inductor coil, L= 25 µH, resistor, R = 20 Q and capacitor, C = 4.894 nF. (i) Determine the center frequency of the bandpass filter. (ii) Determine the quality factor of the tuned circuit. (iii) Determine the bandwidth of the bandpass filter. (iv) Find the upper and lower cut frequency for the bandpass filter. (v) Plot the 3 dB bandwidth of the bandpass filter.

For an AM superheterodyne receiver, station A with RF signal of 1000 kHz uses high side injection to receive the signal. A tuned circuit for a bandpass filter has inductor coil, L= 25 µH, resistor, R = 20 Q and capacitor, C = 4.894 nF. (i) Determine the center frequency of the bandpass filter. (ii) Determine the quality factor of the tuned circuit. (iii) Determine the bandwidth of the bandpass filter. (iv) Find the upper and lower cut frequency for the bandpass filter. (v) Plot the 3 dB bandwidth of the bandpass filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

in FM , the maximum allowable frequency deviation is 4kHz and the frequency deviation by noise is 156.42HZ? then the signal to noise ratio is .......
what is the comparison and contrast of Amplitude Modulation,Single Sideband and Double Sideband?
How it is generated Single Sideband Modulator Using Filter Method
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
A product detector has a 27-MHz carrier and is used to pass audio frequencies from 200-Hz to 15-KHz range. What is the approximate center frequency of the filter needed to pass the lower sideband is used?
iv. When the half power point bandwidth is 10 MHz and the center frequency is 5MHZ, the quality factor is (a) 2 V. In three phase system, the two Wattmeters meter method can be used to measure. (a) The power in two phases (b) The total power vi. The low pass filter allows.... (b) 20 (c) 0.5 (c) The power in one phase. only to pass. (b) Low frequencies (c) (a) and (b) (a) High frequencies
For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
Discuss the action of the filter circuit?
A Spectrum Analyzer is used to measure: a) Power in da of Fundamental and Harmonic Frequencles b) Power in dB of Fundamental and intermodulation Distortion Products c) Voltages in de of Fundamental and Intermodulation Distortion Products. d) Both a andb
Using half width pulses, derive the power spectral density and bandwidth for 1. Unipolar signals 2. Polar signals. 3. Bipolar signals.
1) From the plots, what is the frequency of the input signal (in samples as well as radians)? 2) From the plots, what is the frequency of the output signal (in samples and radians)? 3) What does echo do to the magnitude and phase spectra?
A Superheterodyne receiver is to tune the range from 1MHz to 3.6MHz, with an IFof 500kHz. The local oscillator frequency is always higher than the incoming RFsignals. a. Determine the capacitance tuning ratio of the variable capacitor of theRF circuitb. Determine the capacitance tuning ratio of the variable capacitor of thelocal oscillator circuitc. Calculate the frequency of the local oscillator if the receiver is tuned to3MHZd. Calculate the image frequency of 3MHze. Calculate the Image Frequency Rejection Ratio (in dB) of the receiver if itis tuned to 3MHz and the F filter selectivity is 100