FOR 3:00p.m. SOLAR TIME, ON JULY 21, IN BOISE, ID, A Bft WIDE AND 5ft HIGH WINDOW FACES SOUTH WEST. (ACTUALLY, IT FACES SOUTHWEST ALL THE TIME!) THE NEW INOPERABLE WINDOW HAS A 2in. WIDE ALUMINUM FRAME WITH A THERMAL BREAK UTILIZING METAL SPACERS. THE GLAZING SYSTEM IS 21C IN TABLE 7-3. THERE IS NO INTERIOR OR EXTERIOR SHADING. CALCULATE THE TOTAL SOLAR HEAT GAIN, USING THE SIMPLIFIED APPROACH.

FOR 3:00p.m. SOLAR TIME, ON JULY 21, IN BOISE, ID, A Bft WIDE AND 5ft HIGH WINDOW FACES SOUTH WEST. (ACTUALLY, IT FACES SOUTHWEST ALL THE TIME!) THE NEW INOPERABLE WINDOW HAS A 2in. WIDE ALUMINUM FRAME WITH A THERMAL BREAK UTILIZING METAL SPACERS. THE GLAZING SYSTEM IS 21C IN TABLE 7-3. THERE IS NO INTERIOR OR EXTERIOR SHADING. CALCULATE THE TOTAL SOLAR HEAT GAIN, USING THE SIMPLIFIED APPROACH.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.55P

See similar textbooks

Similar questions

(10-23) The shown four offices are to be heated by warm air heating system. The following data are given: The calculated heating loads for the offices are: Q₁ = 3,465 W, Q₂ = 2,755 W, 3 = 2,615 W and Q=2,895 W. Inside design temperature is 20°C. Warm air temperature and velocity leaving the furnace are 55°C and 5 m/s, respectively. Density and specific heat of air are 1.15 kg/m³ and 1.005 kJ/kg-K, respectively. Calculate the followings: (a) Supply volumetric flow rate of air to each office. (b) Diameters of duct system for all offices using equal pressure drop method. (c) Pressure drop of the longest duct run. (d) Select a fan type and model to satisfy the above requirements. State the capacity and pressure rise of the selected fan. 25 A Furnace Room -2.0- -4.0- B Office 1 2.5 -3.0- C Office 2 -3.0- D Office 3 *Dimensions in meters -3.0- E Office 4 3.5
What is shape function? Derive linear shape functions for 1- dimensional bar element in terms of natural coordinate. Also plot variation of shape functions within this element. please don't do it by hand, the letter gets in the way, make it typeable.
The below shown graph is drawn from the tabulated values of brass which we measured during the experiment of thermal conductivity: (Consider the value of heater power (Q') and the area of cross section (A) of the material from the tabulated values) X-axis 1 unit = 1cm vaxis 1 unit s'c 70- 20- 10- Distance of the test point from the hot end in centimeter Calculate the following: Thermal conductivity of brass Calculated Value quantities Difference in temperature (AT) C° (with sign) Difference in distance between test points (Ax) cm Slope from the graph °C/m (with sign) Thermal conductivity of brass kp W/m°C
Match the surfaces 17-20 to their characteristic: principal, inclined, or curved
Describe and compare the modes of heat loss through the single-pane and double-pane window assemblies shown in the sketch below.
1.80 Describe and compare the modes of heat loss through the single-pane and double-pane window assemblies shown in the sketch below. Problem 1.80
Compute the dimensions of the rectangle shown in Fig. (b) that has the same kx and ky as the W867 section in Fig. (a). (See Prob. 9.13 for properties of W867. ) Problems 9.15â€”9.29 are to be solved using the method of composite areas.
Calculate the total heat gains of the window below. Dimension: 9' by 15' Materials: 1" insulating glass, 1/4" lites, clear Note: SC = 0.38 due to blinds Orientation: South Time: When SHGC peaks for the South orientation on July 21, 40 N Temperature difference between design and outdoor: 33 F
1. The circled feature is an example of what kind of design (explain your choice): (a) Aesthetic design (b) Design for manufacture (c) Human centered design (d) Design to minimize environmental impact (e) Design to maximize strength When Connecting for Use & Checking Leaks * cew vers o Leden www EYES wwwwwww 24 st is made SON ME" L y plane WASTAN MAK STARA Procedures the S w con the care NA J 250 x SAN. Lowe
The surface area of an unclothed person is 1.5m ^2 and thier skin tempature is 33 degree celcius. This ideal person is located in a room with a tempature of 65 dregrees F. and has an emissivity of e=0.95 suppose the room has dimensions 4mx9mx18m a) suppose you and your closest 10 friends come into this room and heat it up. suppose your clothes are in equilibium with your skin and have the same tempature and emissivity. Further suppose that your net power into the room remains constant . How long does it take before the room to get to hot say 95 degrees
image82
12. Depicted below is the side-view sketch of a breakfast barishelf that I built several years ago. The bar was 5-foot long and 24 inches wide. It was supported by a single strut (member) that was anchored to the wall at a distance of 30 inches below the shelf (shown a location C on the sketch). The strut was connected to the shelf at a location B which was 18 inches away from the wall. Of course, the bar top itself was also anchored to the wall at location A. All connections at locations A, B, and C are being modelled as frictionless pins in the sketch. Compute the X direction force at location A if I loaded 100 pounds of Groceries (G) on the shelf and the Center of the Gravity of the Groceries was located 4 inches inward of the right- hand edge of the bar. Ignore the thickness of the shelf and the strut. This is a Frame question because the shelf is a three-force member. Ax = wall 244 4=100 Pounels Shelf 3.