Find the force in members AB, AC, BC, Bd, CD and CD for truss shown in Fig 4-3.17. Assume that the loads P are zero and that each load Q = 4000 lb Figure P-4-3.16D.60° 60B.H.75°60°60°75°60°60°60°60°60°IC3045030°45°0/-Figure P-4-3.17-10'10'-10'-E) 4-3.17. Find the force in members AB, AC, BC, BD, CD, and CE forthe truss shown in Fig., P-4-3.17. Assume that the loads P are zero andthat each load () = 4000 lb.%3DBD=5660 1lb C; CE = 6940 lb T4-3.18. Repeat Prob. 4-3.17 if the loads Q are zero and each loadP32000 lb.4-3.19. Repeat Prob. 4-3.17 if each load P = 1500 1lb and each loadP32500 lb.%3D%3DBD =4440 lb C; CE = 5065 lb T%3D

Answered: Image /qna-images/answer/f1df1b18-d151-42bb-ac05-532ac483283d.jpg

Answered: Find the force in members AB, AC, BC,…

Find the force in members AB, AC, BC, Bd, CD and CD for truss shown in Fig 4-3.17. Assume that the loads P are zero and that each load Q = 4000 lb

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.20P: A plane Frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin...

See similar textbooks

Related questions

Q: A cylinder rests on the 90° corner as shown. The tension P in the string is gradually increased unti...

Q: Q.44. Give the different parameters value for different dielectric used in cable. Also, describe the...

A: When an electric field is applied to a dielectric material, electric charges do not flow through...

Q: of degrees of fre sm shown below

Q: Which of the following statements regarding the “Pre-Emission Inspection Check” Of a diesel powered ...

A: Given Data: Which of the following statements regarding the “Pre-Emission Inspection Check” Of a die...

Q: determine the force member BD and CD (kN)

Q: A titanium cylinder having a diameter of 50 mm in diameter and 540 mm long falls inside a vertical t...

Q: 100 mm diameter of a shell and a height of shell is 100 mm with the corner radius of 0.4 mm is to be...

Q: 1. Temperature field. Let the isotherms (curves of constant temperature) in a body in the upper half...

A: On a map or chart, an isotherm is a line that connects places with the same temperature. In meteorol...

Q: Question 2 A mass of 5 kg is supported on two springs, the stiffness of the springs being 2000 N/m ...

Q: Knowing that, ignoring air resistance, an apple falling from a height h hits the ground when 2h If y...

A: Given Data

Q: A water container is kept on a weighing balance. Water from a tap is falling vertically into the con...

A: Given:Volume flow rate of water=Q,velocity of water=U,total mass(container+water)=m,

Q: The company is interested in expanding its production capability into ceramic based products. You h...

A: Sintering techniques are broadly classified into two types: solid state sintering and liquid pha...

Q: The angle plate is subjected to the two 250-N forces shown. It is desired to replace these forces by...

Q: If longitudinal strain for a wire is 0.03 and its Poisson's ratio is 0.5, then its lateral strain is

A: To find : Lateral strain Explanation : Strain is defined as the change in dimension upon original d...

Q: Explain the relationship between the answers for (a) and (b).

A: we have to determine the saturation pressure of liquid water & vapor @ 100 Celcius

Q: tween two cities 60mi apart take if, a. It's going downstream where the current is 3mph b. It's goin...

Q: ue of specifie 7.0 cal/mole

Q: When checking the fifth wheel, coupling device, the Certified Inspector must check the condition and...

A: Answer = True

Q: Solve the following problems. Be sure to show your work. Answer without work shown will receive no c...

A: Drawing equivalent load diagram. and calculated magnitude and location of the resultant force with r...

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the correspon...

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000 wv=πdN60=π×0...

Q: 8. The potential energy of an apple is 6.00 joules. The apple is 3.00-meters high. What is the mass ...

A: GIVEN DATA - h=3m POTENTIAL ENERGY P.E.=6J WE HAVE TO FIND MASS OF APPLE

Q: An Actual Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. ...

Q: A body starts with a initial velocity of 26m/s and moves with the constant acceleration of 7ms-2 for...

Q: Determine the shear strain yry at corners A and B if the plastic distorts as shown by the dashed lin...

A: In the following figure we have to determine the shear strain at corners A and B.

Q: Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ri...

Q: Sment č Drpm for

Q: The state of stress is plane stress and it is shown on the element. What is the normal stress on the...

A: Given data : Normal stress in X direction σX=40 MPaNormal stress in Y direction σY=-60 MPaShear stre...

Q: A constriction in a pipe will cause velocity to increase and pressure to fall at the throat. The pre...

Q: Deter mile State spo ce rehg1esentection O/p > 3) 4Nm 3N-m 3N/p fits + 3 kg 3 N/m 3N-S/m 2 N-5/m IN-...

Q: Q.13 The following specifications are glven for a rigid coupling. Outside diameter of flanges = 160 ...

Q: transfer with air. If the air side heat transf It is proposed to coat a 1 mm diameter wire w enamel ...

A: Given:diameter of wire, d=1 mmradius, r=d2=0.5 mmthermal conductivity, k=0.1 W/m.Kheat transfer coef...

Q: m, L A

Q: A projectile is fired with an initial velocity of 60 m/s upward at an angle of 30 degrees to the hor...

Q: er (in Watts) in the firs erature of 100°C over i

Q: A cantilever beam made of carbon steel of circular cross section as shown in Fig. is subjected to lo...

Q: • The shaft whose torque varies from 2000in-lb to 6000in-lb has 1.5" diameter and a yield strength v...

Q: am is rotating with c Gu

Q: he company is also interested in expanding its production capability into composite based products....

A: Filament winding is an automated open moulding method that employs a revolving mandrel as the mou...

Q: Determine the reactions at supports A, C,

A: Need to determine the reactions At supports A,C and D

Q: Determine the force due to hydrostatic pressure on the flat vertical side of a tank which has the sh...

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine...

Q: uck return mechanis is 180mm. The incli

Q: A rigid steel bar is supported by three rods, as shown. There is no strainin the rods before the loa...

Q: - A circular shaft is subjected to a torque 'T and a bending moment M. The ratio of maximum shear st...

A: Find the ratio of maximum shear stress to maximum bending stress.

Q: Magnetic resonance imaging (MRI) is a medical imaging technique that located in hospitals and radiol...

A: Any product, gadget, implant, or equipment that provides no known dangers in the MRI environment...

Q: mal condu

Q: U4.1 A. Determine the magnitude that the water exerts on walls AB and DC, and on the bottom BC, usin...

A: Here Width = 4 m CD = 1 m BC = 8 m AB = 2.5 m

Q: Chesterfield currently uses 11,400 m³/d (average flow) of water which is drawn from a storage reserv...

A: Given data: Average flow per day = 11400 m3 Minimum flow during winter = 0.25 x Average flow Peak fl...

Q: 1. A block weighing 400 N is pulled along a level from at a constant speed by a rope which makes 40°...

A: As per given question F=220N Mass =400N Angel =40° We have to determine cofficient of friction

Q: A composite axial structure consists of two rods joined at flange B. Rods (1) and (2) are attached t...

A: Find the force and stresses each members and deflection of point B A1=780mm^2 A2=1100mm^2 E1=40Gpa E...

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Find the force in members AB, AC, BC, Bd, CD and CD for truss shown in Fig 4-3.17. Assume that the loads P are zero and that each load Q = 4000 lb

Figure P-4-3.16
D.
60° 60
B.
H.
75°
60°
60°
75°
60°
60°
60°
60°
60°
IC
30
450
30°
45°
0/-
Figure P-4-3.17
-10'
10'-
10'-
E)

4-3.17. Find the force in members AB, AC, BC, BD, CD, and CE for
the truss shown in Fig., P-4-3.17. Assume that the loads P are zero and
that each load () = 4000 lb.
%3D
BD=5660 1lb C; CE = 6940 lb T
4-3.18. Repeat Prob. 4-3.17 if the loads Q are zero and each load
P32000 lb.
4-3.19. Repeat Prob. 4-3.17 if each load P = 1500 1lb and each load
P32500 lb.
%3D
%3D
BD =4440 lb C; CE = 5065 lb T
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A soccer goal is subjected to gravity loads (in the - z direction, w = 73 N/m for DG, BG, and BC; w = 29 N/m for all other members; see figure) and a force F = 200 N applied eccentrically at the mid-height of member DG. Find reactions at sup ports C, D, and H.
Find support reactions at A and D and then calculate the axial force N, shear force V, and bending moment M at mid-span of AB. Let L = 14 ft, q0 = 12 lb/ft, P = 50 lb. and = 300 lb-ft.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house painter and the distributed weight (u) of the ladder itself. Find support reactions at A and B: then plot axial force (N), shear (V), and moment (M) diagrams. Label all critical N, V, and M values and also the distance to points where any critical ordmates are zero. Plot N, V, and M diagrams normal to the inclined ladder. Repeat part (a) for the case of the ladder suspended from a pin at B and traveling on a roller support perpendicular to the floor at A.
A plane truss has a pin support at F and a roller support at D (see figure). (a) Find reactions at both supports (b) Find the axial force in truss member FE.
Consider the plane truss with a pin support at joint 3 and a crtica1 roller support at joint 5 (see figure). (a) Find reactions at support joints 3 and 5. (b) Find axial forces in truss members 11 and 13.
Find expressions for all support reaction Forces in the plane frame with load 3P applied at C as shown in the figure. Joints A and D are pin supported, and there is a roller support at joint F. The lengths and the properties of the members are shown in the figure. Neglect the weights of all members. Select Rfas the redundant.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A plane Frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin connected at B. A triangularly distributed lateral load with peak intensity of SO N/m acts on CD. An inclined concentrated force of 200 N acts at the mid-span of BC. (a) Find reactions at supports A and D. (b) Find resultant forces in the pins at B and C.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
Space Frame ABC is clamped at A, except it is free to rotate at A about the x and y axes. Cables DC and EC support the frame at C. Force Py= - 50 lb is applied at the mid-span of AS, and a concentrated moment Mx= -20 in-lb acts at joint B. (a) Find reactions at support A. (b) Find cable tension Forces.
The roof over a concourse at an airport is supported by the use of pretensioned cables. At a typical joint in the roof structure, a strut AB is compressed by the action of tensile forces Fin a cable that makes an angle = 75° with the strut (see figure and photo). The strut is a circular tube of steel (E = 30,000 ksi) with outer diameter d2= 2.5 in. and inner diameter d1= 2.0 in. The strut is 5.75 ft long and is assumed to be pin-connected at both ends. Using a factor of safety n = 2.5 with respect to the critical load, determine the allowable force F in the cable.