Find the charge q(t) on the capacitor and the current i(t) in the given LRC-series circuit. L = 1 h, R = 100, C = 0.0004 f, E(t) = 30 V, q(0) = 0 C, i(0) = 5 A 4-30t 250€ 6 -30t 4 + te + с 250 q(t)=250 i(t) A Find the maximum charge on the capacitor. (Round your answer to four decimal places.) x c

Find the charge q(t) on the capacitor and the current i(t) in the given LRC-series circuit. L = 1 h, R = 100, C = 0.0004 f, E(t) = 30 V, q(0) = 0 C, i(0) = 5 A 4-30t 250€ 6 -30t 4 + te + с 250 q(t)=250 i(t) A Find the maximum charge on the capacitor. (Round your answer to four decimal places.) x c

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 6PP: In an RLC parallel circuit, the resistor has a resistance of 60 , the inductor has a reactance of...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
In an RLC parallel circuit, the resistor has a resistance of 60 , the inductor has a reactance of 180 , and the capacitor has a reactance of 80 . Find the circuit power factor.
An RL circuit with a 8-ohm resistor and a 0.08-H inductor carries a current of 1 A at t = 0, at which time a voltage source E(t) = 8 cos (90t) V is added. Determine the subsequent inductor current and voltage.
The input to the circuit shown in the figure below is the voltage V(t) = 4e-20 t V for t > 0 The output is the current i(t) = -1.2e-20t V for t > 0 The initial inductor current is iL(0) = -3.5 A. Find the values of inductance L and resistance R. Please answer in typing format solution please
A capacitor is initially charged up to 10V. Plot the output viltage, Vo(t) = VPe – t/tau, waveforms for C = 1mF, 5mF, and 10mF and mark the Vo(t=tau) value in the same graph. Note that tau is a time constant (tau = RC) of the circuit.
Find the charge on the capacitor in an RLC seriescircuit whereL = 2 H,R = 24Ω,C = 0.005 F, andE(t) = 12sin10t V. Assume the initial charge on thecapacitor is 0.001 C and the initial current is 0 A.
In an RC series circuit, ε = 12.0 V, R = 2.00 MΩ, and C = 2.39 µF. (a) Calculate the time constant. (b) Find the maximum charge that will appear on the capacitor during charging. (c) How long does it take for the charge to build up to 14.3 µC?
A 1-F capacitor and initially starts with vC(0) = 0V. (a) Determine iC(t) when vC(t) = x(t), where vC(t) has units of V. (b) Determine vC(t) when iC(t) = x(t), where iC(t) has units of A. Hint: don’t forget the initial conditions. Answer: (0, 4, −4, 0)A, 0V, (2t2−4t+2)V, (−2t2+12t−14)V, 4
111. A capacitor bushing forms arm ab of a Schering bridge and a standard capacitor of 500 pF capa citance and negligible loss, forms arm ad. Arm bo consists of a non-inductive resistance of 300 S2. When the bridge is balanced arm cd has a resis- tance of 72.6 12 in parallel with a capacitance of 0.148 uF. The supply frequency is 50 Hz. Calculate the capacitance and dielectric loss angle of capacitor. Derive the equations for balance and draw the phasor diagram under conditions of balance. [Ans. 121 pF; 0.00338 rad] 16.
Problen the following: A. The voltage across the capacitor at the t = 0. B. The voltage across the capacitor for t > 0. C. The voltage across the 32K resistor for t > 0. Given RC circuit with a switch that moves from position A to B at time t =0 obtain
Method: Transient AnalysisAn electronics hobbyist is working on a circuit that includes two capacitors, an inductor, and two resistors. The capacitors are C1 with a capacitance of 20 microfarads and C2 with a capacitance of 10 microfarads. The inductor, L1, has an inductance of 10 millihenries. The resistors are R1 with a resistance of 500 ohms and R2 with a resistance of 200 ohms. The voltage source provides 25 volts at a frequency of 1000 Hz. The hobbyist would like to know the current and voltage across each component in the circuit at 20 milliseconds and 100 milliseconds after the voltage source is turned on. Can you help the hobbyist determine these values?SHOW STEP BY STEP SOLUTION
At t = 0, the switch S is closed and the capacitors are uncharged. Find the charge stored on capacitor C2 in steady state (t -> infinity). R1 = 2R, R2 = 2R, R3 = 3R, R4 = 2R, R5 = 3R, C1 = 6, C2 = 6.