Figure 2.7 Fluid sample TO Саpillary tabe (P1 – P2)D² 32vL A capillary type viscometer similar to that shown in Fig. 2.7 is being used to measure the viscosity of an oil having a specific gravity of 0.90. The following data apply: Tube inside diameter = 0.100 in = D Length between manometer taps = 12.0 in : = L Manomete fluid = marcury

Figure 2.7 Fluid sample TO Саpillary tabe (P1 – P2)D² 32vL A capillary type viscometer similar to that shown in Fig. 2.7 is being used to measure the viscosity of an oil having a specific gravity of 0.90. The following data apply: Tube inside diameter = 0.100 in = D Length between manometer taps = 12.0 in : = L Manomete fluid = marcury

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER CORK 60 CC- RESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Explain the operation procedures and constraints of the different viscometers especially the used one. b) Explain, with examples, the effects of temperature and shear forces on theNewtonian and non-Newtonian fluids. c) Illustrate the results of the viscosity test of the above motor oil then f it the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Takeu at T = 0°C. То + c T 10 In- = a + b Mo T d) What is the viscosity of the used above equation motor oil at 280 K, 305 K and 3 20 K? You can use the
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
A "dead-weight" pressure testing machine as shown in Fig. Q5b is used to measure the accuracy of a Bourdon pressure gauge. If the weight and piston together weigh 200 N and the piston diameter is 2.5 cm, find the percentage error of the Bourdon pressure gauge if it indicates a pressure of 350 kPa. Piston weight Fig. Q5a oil Pressure gauge [3 marks]
The kinematic viscosity of liquid oil (10³) C.S (1 stoke =100 C.S) and relative density = 0.92. Find the viscosity of the fluid oil in c.g.s and SI %3D systems.
QI A ball made of INOX AISI 365 steel with density of 8.52 gricm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m'.
(5) Pressure Cooker (6) Carburetor (7) Radiator of an automobile. 2. Convert the following reading of pressure to kPa, assuming that the barometer reads 760mm Hg. (1) 90cm Hg gauge (2) 40cm Hg vacuum (3) 1.2m H20 gauge 3. Five masses in a region where the acceleration due to gravity is 30, 5 ft/s are as follows: m, is-
.ll GH Vodafone LTE 6:38 AM © 85% 4 Today Edit 6:36 AM .ll GH Vodafone LTE 6:36 AM @ 84% 4 MCE 243 Note New.pdf Question 3 A multi-fluid container is connected to a U-tube manometer as shown in fig below. For the given specific gravities and fluid column heights, determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. 70 cm Oil SG - 0.90 30 cm Water 90 cm Glycerin 20 сm 15 cm 25 orldre
Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Determine (a) pressure in MKS unit, (b) pressure in CGS unit, (c) the viscosity of the liquid, (d) If the weight was given as 8.5 grams, what will be the density of the liquid? (e) the kinematic viscosity of the liquid? (f) and the fluidity of the liquid?
Q1. A concentric cylinder viscometer is driven by a falling mass M connected by a cord and pulley to the inner cylmder. Annular gap of width a and height H has been filled with liquid to be tested. The speed of the falling mass is Vim. Develop an algebraic expression for the viscosity of the liquid. Evaluate the viscosity of the liquid using M= 0.1 Kg, R=50mm, H=80 mm, r-25mm, =0.20mm and Vim = 30 + ww XX Cord Puliey,
A U-tube manometer filled with water, density 62.4 Ibm/ft^3, shows a height difference of 10 in, what is the gauge pressure? 2.488 kPa 52.0 psf 3.537 atm 2.488 psi
flued mechanics The inclined manometer at Fluid Dynamic laboratory at E5 has broken. You are tasked to design a new inclined manometer as shown in Figure 1. The design task is to decide what is the proper manometric fluid to be used, angle of inclination (θ), and the length of the vertical (L1) and inclined (L2) leg of the manometer. Since the manometer is mainly used together with Pitot-Static tube to measure air velocity it needs to be sensitive to a small pressure difference which in the range of 5 to 50 Pa. It should be notice that the manometer should fit in a compartment which has 15 cm-height and 80 cm-length. The inclination angle should be at least 5°. The temperature in the lab is around 27 °C to 37 °C. The manometric fluid should fulfil the following criteria: The fluid should have a low vapour pressure (A liquid with high vapour pressure would be less sensitive to changes in pressure) The fluid should have low surface tension to avoid the capillary rise. High boiling…
Q1: the pressure at point A is 172 pa. All fluids are at 20°C. The air pressure in the closed chamber B is..[w(water)=9790 * N/m³,w(SAE oil 30)=8720 N/m³] Air B SAE 30 oil Liquid, SG = 1.45 5 cm 3 cm 4 cm 6 cm A Water S cm 3 cm