Example 12.22 100,000 kg engine is moving up a slope of gradient 5 at a peed 100 m/s. The coefficient of friction between the engine and the rails is 0,1. If the engine has an efficiency of 4% for converting that into work, find the amount of coal, the engine has to burn up in one hour (Burning of 1 kg of coal yields 50,000 joules)

Example 12.22 100,000 kg engine is moving up a slope of gradient 5 at a peed 100 m/s. The coefficient of friction between the engine and the rails is 0,1. If the engine has an efficiency of 4% for converting that into work, find the amount of coal, the engine has to burn up in one hour (Burning of 1 kg of coal yields 50,000 joules)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at 200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, angle of lap 160° and maximum tension in the belt is 2500 N.
cases if in both the cases. Example 12.22 A 100,000 kg engine is moving up a slope of gradient 5° at a speed 100 m/s. The coefficient of friction between the engine and the rails is 0,1. If the engine has an efficiency of 4 % for converting that into work, find the amount of coal, the engine has to burn up in one hour (Burning of 1 kg of coal yields 50,000 joules).
A petrolengine has mechanical efficiency 0.8 and lower calorific value of ispoots 44.2 MJ/kg. The engine bore 0.06 m and stroke of 0.08 m. The engine speed of 2000 rom. The consumption of fuel about 8 liter/h and the brake welght is 200N. Take the density of fuel as 750 kg Im3 and torque arm of A00 mm Find the specific fuel consumption.
Four turns of rope wrapped around a horizontal post will hold a 1000 lb weight with a pull of 10 lbs. Find the coefficient of friction between the rope and the post
A uniform push of 150N, applied at an angle of 30 degrees to a 20kg block which rests on a horizontal surface, gives the block a velocity of 6.5m/s in 4s. Find the coefficient of kinetic friction
A sled of mass 500kg sits at rest on a rough slope that is inclined at 10* to the horizontal. The coefficient of friction between the slope and the sled is 0.3. The sled is held in place by a wire attached to a winch. The tension in the wire is TN. a) Find the maximum possible value of T. A load of mass mkg is added to the sled, and tension in the wire is increased to 5000N in order to pull the sled and load up the slop. Given that the sled and load are pulled a distance of 100m in 80seconds, b) Work out the value of m
Question 4 A pulley is driven by a flat belt, the angle of lap being 120°. The belt is 100 mm wide by 6 mm thick and density is 1000 kg/m. If the coefficient of friction is 0.3 and the maximum stress in the belt is not to exceed 1.5 MPa. Calculate: 4.1. 4.2. the speed of the belt in m/s using the information related to driving pulley. the centrifugal tension and the tension on the first tight side of the belt T1. the greatest power the belt can transmit. 4.3
A block of mass 14 kg is resting on a table is pulled by a force of 100 N. The coefficient of friction between table and block is .34. Calculate the acceleration of the block.
a. derive Hagen-poiseuille equation from the friction factor given.
FRICTIONLESS Find the downward acceleration of m1 if it has a mass of 27.8 kg.
The diagram below represents an elevator used to lift concrete blocks to upper levels on a construction site. The belt travels at a velocity of 0.9 m/s and is inclined at 26° above the horizontal plane. A yolluy € ф 300 mm 008 to NOT TO SCALE alaups 1909 provided to come Calculate the frictional force and the coefficient of friction between each block and the belt. Each block weighs 16.5 kg. Frictional Force: N Coefficient of Friction: ..........