Thermodynamics/fluid mechanics problem is in image. Air flows in a nozzle, and at a givensection following properties are known.Po2.- |1OKPA ; P= 100 KPa ; T NA 20 C,li) The total (stagnation) temperature (To) is (in KJ,is a. 360 ; b. 340; c. 320 ; d. 300;e 280(ü) The velecity of slow (V) is (im m/sec),a. 108 ; b. 128 ; c. 148; d.168;e. 188

To find Total stagnation temperature velocity of flow

Answered: E) The total (stagnation) temperature…

E) The total (stagnation) temperature (To) is (in Ko ig a. 360; c. 320 ; d. 300;e 280 b.340; -) The velocity of flow (V) is (in m/sec), a. 108; b.128 ; C. 148;d.168 ;e. 188

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The compressed air network of a foundry with a volume V = 30 m³ is filled by a compressor in 47 = 30 min. Therefore the state of the air changes from pi = 0.15 MPa, t₁ = 25 °C to p2 = 1.0 MPa at constant temperature. a) Which mass of air Am is fed into the compressed air network? b) Which air volume flow Vo in the intake state of the compressor (po = 1000 hPa, to = 10 °C) is required for filling? The air mass flow required for a pneumatic hammer is subsequently provided in state 3 from the compressed air network. The pressure is throttled adiabatically to p3= 0.5 MPa, the air volume flow is V3 = 1.4 m³/min. c) What is the air mass flow m required by the hammer? d) What power P34 does the adabatic pneumatic hammer deliver, if a temperature t4 15 °C is measured at the air outlet?
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5 m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.
dp 1. It shows that the behavior of fluid is A From the equation stated, show the formula for mass flow rate AVp = c. :C.
At 300 degrees Celsius and 1 atmosphere, air moves at 0.9 times the speed of sound. The specific heat at constant pressure to specific heat at constant volume ratio for air is 1.4. a. So what was the air velocity in this situation (in m/s)? b. What is the temperature of stagnation (in K)?
A tank contains air at stagnation properties of 200 kPa and 30 C. A vent of 3 cm diameter is opened. a) Find air flow rate if Pb = 150 kPa and b) if Pb = 101.35 kPa. [Ans.: For Cd = 1, a) 0.29 and b) 0.33 kg/s].
1-In-compressible fluid flow in pipe line, there are two kinds...... a- Transition & turbulent flow c- laminar & turbulent flow. b- laminar & Transition flow. d- Other. 2- The viscosity actually a is the resistance of the internal material movement and that because of..... ...between molecules. a- the cohesion forces. b- Buoyancy force. c- the adhesion forces. d-Other. 3- calculate the surface tension of liquids and solutions using the following mathematical relationship: ******** a-Y-0.5h+p-g/r. b-Y-0.5 h pgr. c-Y-(h* p*g*r)*5. d-Other.
Patm 1. Initially; the piston sits on the stops and the linear spring exerts no force, the specific volume is 0.05 m /kg and the pressure is 125 kPa. Atmospheric pressure is 100 kPa, mass of the piston is 102 kg, and area of the piston is 200 cm?. The linear spring exerts a force on the piston in such a way that the specific volume becomes 0.08 m'/kg when the pressure reaches 200 kPa. Heat is transferred to the water until its temperature is 115 °C. Calculate work and heat transfer, showing the process on a P-v plot. Hint: In the final stage, the temperature is 115°C, but the pressure is not given. You need to find P and v using the tables and P-v plot.
During actual processes of → expansion and compression of gases, the pressure and volume are usually be related to a process called polytropic, whose pressure can be expressed as P = CV-n where n is the polytropic exponent, and this can be equal to unity or different. a) If n = 1, show and explain the process that occurs and how the work of border? b) If n = 1, what process does the calculation of boundary work resemble, show and explain?
i) Construct the flow chart (diagram) and compute the total heat required to convert 800 g of ice at-50°C to steam at 115 °C. (Cice 2090 J/kg. C, Cwater 4186 J/kg. C, Csteam 2010 J/kg. C, Lf = 3.33 x 10 J/kg, Lv 2.26 x 10 J/kg.)
74. Find the ratio of Mach no.s of an aircraft flies with a velocity greater by 39 m-s1 at 8000 m elevation, (T =- 41 C° at 8000 m) and (T = - 59 C° at 9000 m, M = 2.1). ügs jlio Jojo
Pls.a answer thank you! A cooling tower cools water from 39 °C to 24 °C at the rate of 25 kg/s. Air enters the tower at 18 °C at the rate of 35 kg/s. Find the temperature of air leaving the tower.
THERMODYNAMICS. Question I. 0.04 kg/s of an ideal gas (molecular weight 30, ratio of specific heats 1.5) flows through a duct with a cross sectional area of 10 cm?. The pressure and temperature are 100 kPa and 350 K. What is the velocity of this gas flow, in m/s?