Draw the phasor diagrams for a transmission line (modeled as short transmission line) when supplying a leading, lagging and unity power factor loads. Phasor diagram should include sending end voltage, receiving end voltage, load power factor, and line current. Based on the phasors answer the following: a. For lagging power factor load, is |??| >|??|? True/False b. For leading power factor load, is |??| >|??|? True/False c. For unity power factor load, is |??| >|??|? True/False

Draw the phasor diagrams for a transmission line (modeled as short transmission line) when supplying a leading, lagging and unity power factor loads. Phasor diagram should include sending end voltage, receiving end voltage, load power factor, and line current. Based on the phasors answer the following: a. For lagging power factor load, is |??| >|??|? True/False b. For leading power factor load, is |??| >|??|? True/False c. For unity power factor load, is |??| >|??|? True/False

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

Transmission line conductance is usually neglected in power system studies. True False
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
30) In a lightly loaded long distance EHV lines, line loading is and has a power factor: (A) Capacitive, lagging. (B) Capacitive, leading (C) Inductive, lagging (D) Inductive, leading. please contact me in whatsapp +962782974574
The equivalent circuit of a single phase short transmission line is shown in Figure Q4 (b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4 (b) for the lagging power factor at load point (Vn). ii) Summarize, the impact of voltage regulation and efficiency, if the line resistance and line increases are doubled Figure Q4(b). R XL Vs Vn Figure Q4(b) Load
following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of V,º = 1+ j(0) . S1 Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar
Which Transmission Line Parameter is neglected or ignored in most classifications of Transmission Line Equivalent Circuits? A. The Line Inductance B. The Line Resistance C. The Shunt Conductance D. The Shunt Capacitance
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
Ideally, a dc load line is a straight line drawn on collector characteristic curves between which of the following? Please select one: a. Q Point and shear b. Q Point and saturation c. V_CE (interrupt) and I_C (sat) d. I_b = 0 and I_B = I_C/ß_DC
1.The voltage magnitude and phase angle are the quantities to be determined after load flow analysis for............. bus. 2.The total reactance of the transmission system is reduced by installing a series capacitor. Select one: True False
1/ Power loss due to corona is: a. Inversely proportional to frequency. b. Proportional to frequency. c. Frequency does not effect. d. All these answers are wrong. 2/ We prefer High voltage DC (HVDC) transmission system than High Voltage AC transmission system according to the cost, when: a. The distance of the line is more than B00 km. b. The distance of the line is less than 300 km. c. The distance of the line is equal to 300 km. d. All the above answers are wrong. 3/ HVDC Transmission has lower corona losses than HVAC Transmission because: a. HVDC Transmission tower is less height than HVAC Transmission tower. b. HVDC Transmission system work with zero frequency than HVAC Transmission system of 50 Hz. c. HVDC Transmission currents is uniform distributed in the all cross section of the system conductors than HVAC Transmission due to skin effect. d. All of the above answers are wright.
Describe the effect of resistive load on sending and receiving end voltages, Power transferred and Power factor.
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR