DIRECTIONS: Part 1: Set up a study about types of trusses and its importance and applications. Perform a design and structural analysis for the forces acting on the members of the truss shown in the figure below using the method of joints and the method of sections Make a critical comparison between the two methods Estimate the load in each member of the trusses shown in the figure below Show the detailed calculations and computation of the estimated load. Explain the impact of these calculations on the design of different constructions.

DIRECTIONS: Part 1: Set up a study about types of trusses and its importance and applications. Perform a design and structural analysis for the forces acting on the members of the truss shown in the figure below using the method of joints and the method of sections Make a critical comparison between the two methods Estimate the load in each member of the trusses shown in the figure below Show the detailed calculations and computation of the estimated load. Explain the impact of these calculations on the design of different constructions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 1: Compute for the force in each member of the truss shown in FIGURE 1. Indicate in your solutions if the force is in tension or in compression. FIGURE 1 Height of truss= 0.75 Length of horizontal members= 1.00 60 kN B F 25 kN How many members does the truss have? How many support reactions does the truss have? How many joints does the truss have? Considering the number of supports, joints, and members this truss has, this truss is considered What are the force in member: АВ, ВС, CD, AE, ВЕ, СЕ, ЕF, CF, DF
1. If the following figure, there is a cutout in the fuselage skin-stringer panel and the covering cap is a lid. please give a design layout on the surrounding structure to provide alternate paths to carry the loads and satisfied the strength and weight requirements. Cutout
Assignment-1: Considering the structure shown in the following figure: 1. Calculate the reaction forces in joint A and D. 24 kN 6 m 4 m F 8 m 4 m 12 kN 18 kN
Write a short explanation for the following terms: 1. Tensile, Compressive and Shear Loads 2. Bending, Torsion and Buckling 3. Stress 4. Strain 5. Young's Modulus of Elasticity 6. Design Limit Load & Design Ultimate load 7. Safe-life 8. Fail-safe structure 9. Fatigue 10. Loads on fuselage
Provide schematic diagrams and photos. Explain function of the member for the selected application.Information provided: i) Boundary/end conditions: In this instance, the column is assumed to be fixed at both ends, simulating conditions where the column is integrally connected to the floor slabs above and below, a common condition in many mechanical design contexts. ii) External axial load: Assuming the column supports a floor with a uniformly distributed load, we've calculated the total axial load on the column to be 453.589 kN. iii) Properties of the column: The cylindrical column is composed of steel, a commonly used material with a known Young's modulus (E) of approximately 200 GPa. The steel has a yield stress of around 250 MPa and ultimate stress near 400 MPa. The diameter (d) of the column is 0.3048 m, providing a cross-sectional area (A) of π*(d/2)² = 0.073 m².
using the method of sections , analyse the truss shown in figure 8 below reguarding forces in menbers ED , DF AND FC .
analyze a symmetrically loaded simple truss. The minimum number of members is 10. All joints must have a load. Solve using the following methods: 1A: Method of Joints 1B: Method of Sections
2: Answer briefly the following: 1- The method of joints is used to analyze and design trusses. This method is based on what? (For section A only) 2- Define Simple Truss. (For evening section only) 3- The method of sections is used to analyze and design trusses. This method is based on which principle? (For section B only)
For the overhanging truss shown in figure below, compute the member forces in BC, CE and DE. 5kN 3m IB 2m 2m 5kN 10KN ANS: BC = kN, CE = kN, DE = kN (whole number) Which of the following is/are tensile force(s)? (BC, CE, DE)
Analyze the truss shown in figure-5 using Method of Joints. (CLO-2) 200 N
Warren truss and a series of moving loads are shown in Figure 2. Assuming the loads can travel in either direction along the center of the truss. i) Draw the influence line for the force in member FC. ii) Calculate the maximum force (tension or compression) that can develop in member FC due to series of moving loads which acts along the bottom chords of the truss.
Figure 3: Given the figure, determine the member that will be designed for maximum tension (Note: just write the member designation ex: AD) just indicate the two letters.